|
Network Working Group Request for Comments: 4293 Obsoletes: 2011, 2465, 2466 Category: Standards Track |
S. Routhier, Ed. April 2006 |
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Copyright © The Internet Society (2006).
This memo defines a portion of the Management Information Base (MIB) for use with network management protocols in the Internet community. In particular, it describes managed objects used for implementations of the Internet Protocol (IP) in an IP version independent manner. This memo obsoletes RFCs 2011, 2465, and 2466.
1. The Internet-Standard Management Framework
2. Revision History
3. Overview
3.1. Multi-Stack Implementations
3.2. Discussion of Tables and Groups
3.2.1. General Objects
3.2.2. Interface Tables
3.2.3. IP Statistics Tables
3.2.4. Internet Address Prefix Table
3.2.5. Internet Address Table
3.2.6. Internet Address Translation Table
3.2.7. IPv6 Scope Zone Index Table
3.2.8. Default Router Table
3.2.9. Router Advertisement Table
3.2.10. ICMP Statistics Tables
3.2.11. Conformance and Compliance
3.2.12. Deprecated Objects
4. Updating Implementations
4.1. Updating an Implementation of the IPv4-only IP-MIB
4.2. Updating an Implementation of the IPv6-MIB
5. Definitions
6. Previous Work
7. References
7.1. Normative References
7.2. Informative References
8. Security Considerations
9. Acknowledgements
10. Authors
For a detailed overview of the documents that describe the current Internet-Standard Management Framework, please refer to section 7 of RFC 3410 [9].
Managed objects are accessed via a virtual information store, termed the Management Information Base or MIB. MIB objects are generally accessed through the Simple Network Management Protocol (SNMP). Objects in the MIB are defined using the mechanisms defined in the Structure of Management Information (SMI). This memo specifies a MIB module that is compliant to the SMIv2, which is described in STD 58, RFC 2578 [1], STD 58, RFC 2579 [2] and STD 58, RFC 2580 [3].
One of the primary purposes of this revision of the IP MIB is to create a single set of objects to describe and manage IP modules in an IP version independent manner. Where RFCs 2465 and 2466 created a set of objects independent from RFC 2011, this document merges those three documents into a single unified set of objects. The ipSystemStatsTable and ipIfStatsTable tables are examples of updating objects to be independent of IP version. Both of these tables contain counters to reflect IP traffic statistics that originated in much earlier MIBs and both include an IP address type in order to separate the information based on IP version.
Another purpose of this document is to increase the manageability of a node running IPv6 by adding new objects. Some of these tables, such as ipDefaultRouterTable, may be useful on both IPv4 and IPv6 nodes while others, such as ipv6RouterAdvertTable, are specific to a single protocol.
This MIB does not provide native support for implementations of multiple stacks sharing the same address type. One option for supporting such designs is to assign each stack within an address type to a separate context. These contexts could then be selected based upon the context name, with the Entity MIB and View-based Access Control Model (VACM) Context Table providing methods for listing the supported contexts.
This MIB is composed of a small number of discrete objects and a series of tables meant to form the base for managing IPv4 and IPv6 entities.
While some of the objects are meant to be included in all entities, some of the objects are only conditionally mandatory. The unconditionally mandatory objects are mostly counters for IP and ICMP statistics. The conditionally mandatory objects fall into one of several groups: objects for use in higher bandwidth situations, objects for use with IPv4, objects for use with IPv6, and objects for use on IPv6 routers. In short, it is not expected that every entity will implement all of the objects within this MIB. The reader should consult the conformance and compliance section to determine which objects are appropriate for a given entity.
In both IPv4 and IPv6, there are only a small number of "knobs" for controlling the general IP stack. Most controls will be in a more specific setting, such as for controlling a router or TCP engine.
This MIB defines a total of three general knobs, only two of which are used for both IPv4 and IPv6.
Objects are included for both protocols to enable or disable forwarding and to set limits on the lifetime of a packet (ttl or hop count).
The third knob, the timeout period for reassembling fragments, is only defined for IPv4, as IPv6 specifies this value directly.
Each group of objects is required when implementing their respective protocols.
This MIB includes a pair of tables to convey information about the IPv4 and IPv6 protocols that is interface specific.
Special note should be taken of the administrative status objects. These are defined to allow each protocol to selectively enable or disable interfaces. These objects can be used in conjunction with the ifAdminStatus object to manipulate the interfaces as necessary. With these three objects, an interface may be enabled or disabled completely, as well as connected to the IPv4 stack, the IPv6 stack or both stacks. Setting ifAdminStatus to "down" should not affect the protocol specific status objects.
Each interface table is required when implementing their respective protocols.
The IP statistics tables (ipSystemStatsTable and ipIfStatsTable) contain objects to count the number of datagrams and octets that a given entity has processed. Unlike the previous attempt, this document uses a single table for multiple address types. Typically the only two types of interest are IPv4 and IPv6; however, the table can support other types if necessary.
The first table, ipSystemStatsTable, conveys system wide information. (That is, the various counters are for all interfaces and not a specific set of interfaces.) Its index is formed from a single
sub-id that represents the address type for which the statistics were counted.
The second table, ipIfStatsTable, conveys interface specific information. Its index is formed from two sub-ids. The first represents the address type (IPv4 and IPv6), and the interface within that address type is represented by the second sub-id.
The two tables have a similar set of objects that are intended to count the same things, except for the difference in granularity. The object ID "ipSystemStatsEntry.2" is reserved in order to align the object IDs of the counters in the first table with their counterparts in the second table.
Several objects to note are ipSystemStatsDiscontinuityTime, ipIfStatsDiscontinuityTime, ipSystemsStatsRefreshRate, and ipIfStatsRefreshRate. These objects provide information about the row in the table more than about the system itself.
The discontinuity objects allow a management entity to determine if a discontinuity event that would invalidate the management entity's understanding of the counters has occurred. The system being re- initialized or the interface being cycled are possible examples of a discontinuity event.
The refresh objects allow a management entity to determine a proper polling interval for the rest of the objects.
The following Case diagram represents the general ordering of the packet counters. In order to avoid extra clutter, the prefixes "ipSystemStats" and "ipIfStats" have been removed from each of the counter names.
from from
interface upper
layers
V V
| |
+ InReceives (1) + OutRequests
| |
| |
+--> InHdrErrors (5) +--> OutNoRoutes
| |
| |
+->-+ InMcastPkts (1) |
| V |
+-<-+ |
| |
+->-+ InBcastPkts (1) |
| V |
+-<-+ |
| |
| |
+--> InTruncatedPkts (5) |
| |
| |
+--> InAddrErrors |
| |
| |
+--> InDiscards (2) |
| |
| |
+--------+------->------+----->-----+----->-----+ | InForwDatagrams (6) | OutForwDatagrams (6)| | V +->-+ OutFragReqds | InNoRoutes | | (packets) / (local packet (3) | | | IF is that of the address | +--> OutFragFails | and may not be the receiving IF) | | (packets) | | | | | V OutFragOks | | | (packets) (7) | | | +->-+ ReasmReqds (fragments) +-<-+ OutFragCreates | | | (fragments) | | | | +--> ReasmFails (fragments (4)) +->-+ OutMcastPkts (1) | | | V | | +-<-+ +-<-+ ReasmOKs (reassembled packets) | | +->-+ OutBcastPkts (1) | | V +--> InUnknownProtos +-<-+ | | | | +--> InDiscards (2) +--> OutDiscards (2) | | | | + InDelivers + OutTransmits (1) | | V V to to upper interface layers
(1) The HC counters and octet counters are also found at these points but have been left out for clarity.
(2) The discard counters may increment at any time in the processing path. Packets discarded to the left of InNoRoutes cause the InDiscards counter to increment, while those discarded to the right are counted in the OutDiscards counters.
(3) Local packets on the input side are counted on the interface associated with their destination address, which may not be the interface on which they were received. This requirement is caused by the possibility of losing the original interface during processing, especially re-assembly.
(4) Some re-assembly algorithms may lose track of the number of fragments during processing and so some fragments may not be counted in this object.
(5) InTruncatedPkts should only be incremented if the frame contained a valid header but was otherwise shorter than required. Frames that are too short to contain a valid header should be counted as InHdrErrors.
(6) The forwarding objects may be incremented, even for packets that originated locally or are destined for the local host, if their addresses are such that the local host would need to forward the packet to pass it to the correct interface.
(7) When fragmenting a packet, an entity should increment the OutFragFails counter, rather than the OutDiscards counter, in
order to preserve the equation FragOks + FragFails == FragRqds.
The objects in both tables are spread amongst several conformance groups based on the bandwidth required to wrap the counters within an hour. The base system group is mandatory for all entities. The other system groups are optional depending on bandwidth. The interface specific-groups are optional.
This table provides information about the prefixes this entity is using, including their lifetimes. This table provides a convenient place to which other tables that make use of prefixes, such as the ipAddressTable, may point. By including this table, the MIB can supply the prefix information for all addresses, yet minimize the amount of duplication required in storing and accessing this data. This arrangement also clarifies the relationship between addresses that have the same prefix.
This table is required for IPv6 entities.
This table lists the IP addresses (both IPv4 and IPv6) used by this entity. It also includes some basic information about how and when the address was formed and last updated. This table allows a manager to determine who a given entity thinks it is.
This table is required for all IP entities.
This table provides a mapping between IP layer addresses and physical addresses as would be formed by either Address Resolution Protocol (ARP) for IPv4 or the neighbor discovery protocol for IPv6.
This table specifies the zone index to interface mapping. By examining the table, a manager can determine which groups of interfaces are within a particular zone for a given scope.
The zone index information is only valid within a given entity; the indexes used on one entity may not be comparable to those used on a different entity.
This table is required for IPv6 entities.
This table lists the default routers known to this entity. This table is intended to be a simple list to display the information that end nodes may have been configured with or acquired through a simple system such as IPv6 router advertisements. Managers attempting to view more complicated routing information should examine the routing specific tables from other MIBs.
This table is required for all entities.
This table contains the non-routing information that an IPv6 router would use in constructing a router advertisement message. It does not contain information about the prefixes or other routing specific information that the router might advertise. The router should acquire such information from either the routing tables or from some routing table specific MIB.
This table is only required for IPv6 router entities.
There are two sets of statistics for ICMP. The first contains a simple set of counters to track the number of ICMP messages and errors processed by this entity.
The second supplies more detail about the ICMP messages processed by this entity. Its index is formed from two sub-ids. The first represents the address type (IPv4 and IPv6), and the second represents the particular message type being counted. A given row need not be instantiated unless a message of that type has been processed, i.e., the row for icmpMsgStatsType=X MAY be instantiated before but MUST be instantated after the first message with Type=X is received or transmitted. After receiving or transmitting any succeeding messages with Type=X, the relevant counter must be incremented.
Both of these tables are required for all entities.
This MIB contains several sets of objects. Some of these sets are useful on all types of entities, while others are only useful on a limited subset of entities. The conformance section attempts to group the objects into sets that may be discussed as units, and the compliance section then details which of these units are required in various circumstances.
The circumstances used in the compliance section are implementing IPv4, IPv6, or IPv6 router functions and having a bandwidth of less than 20MB, between 20MB and 650MB, or greater than 650MB.
This MIB also includes a set of deprecated objects from previous iterations. They are included as part of the historical record.
There are several general classes of change that are required.
The first and most major change is that most of the previous objects have different object IDs and additional indexes to support the possibility of different address types. The general counters for IP and ICMP are examples of this. They have been moved to the ipSystemStatsTable and icmpMsgStatsTable, respectively.
The second change is the extension of all address objects to allow for both IPv4 and IPv6 addresses and the addition of an address type object to specify what address type is in use.
The third change is the addition of several new objects to the replacement for a previously existing table such as ipNetToPhysical.
The fourth change is the addition of completely new tables such as ipIfStatsTable and ipDefaultRouterTable. The first is based on the previous statistics groups, while the second is completely new to this MIB.
The somewhat more specific changes that are required for IPv4 follow. Note well: this is not meant to be an exhaustive list and the reader should examine the MIB for full details.
Several of the general objects (ipForwarding, ipDefaultTTL, ipReasmTimeout) remain unchanged.
Most of the rest of the general objects were counters and have been moved into the ipSystemStatsTable. The basic instrumentation should remain the same, though the object definitions should be checked for clarifications. If they aren't already in a structure, putting the counter variables in one would be useful. Several new objects have been added to count additional items, and instrumentation code must be added for these objects. Finally, the SNMP routines must be updated to handle the new indexing.
In addition to the ipSystemStatsTable, the MIB includes the ipIfStatsTable. This table counts the same items as the system table but does so on a per interface basis. It is optional and may be ignored. If you decide to implement it, you may wish to arrange to collect the data on a per-interface basis and then sum those counters in order to provide the aggregate system level statistics. However, if you choose to provide the system level statistics by summing the interface level counters, no interface level statistics can be lost - if an interface is removed, the statistics associated with it must be retained.
The ipAddrTable has, loosely, been converted to the ipAddressTable. While the general idea remains the same, the ipAddressTable is sufficiently different that writing new code may be easier than updating old code. The primary difference is the addition of several new objects. In addition, the ipAdEntReasmMaxSize has been moved to another table, ipv4InterfaceTable. As above, the SNMP routines will need to be updated to handle the new indexing.
The ipNetToMediaTable has been moved to the ipNetToPhysicalTable. These tables are fairly similar and updating the old code may be straightforward. As above, the SNMP routines will need to be updated to handle the new indexing.
Two new tables, ipv4InterfaceTable and ipDefaultRouterTable, are required as well as several new ICMP counters.
Finally, there are several tables that are required for IPv6 but are optional for IPv4 that you may elect to implement.
The somewhat more specific changes that are required for IPv6 follow. Note well: this is not meant to be an exhaustive list and the reader should examine the MIB for full details.
Two of the general objects, ipv6Forwarding and ipv6DefaultHopLimit,
have been renamed and given new object identifiers within the ip
branch but are otherwise unchanged. The new names are
ipv6IpForwarding and ipv6IpDefaultHopLimit.
While there is an ipv6InterfaceTable that contains some of the pieces
from the ipv6IfTable, the two are somewhat different in concept. The
ipv6IfTable was meant to replicate the ifTable while the
ipv6InterfaceTable is meant to be an addition to the ifTable. As
such, items that were duplicated between the ifTable and ipv6IfTable
have been removed and some new objects added.
The ipv6IfStatsTable most closely resembles the ipIfStatsTable with
an additional index for the address type and most of the
instrumentation should be re-usable. Some new objects have been
added to the ipIfStatsTable. As above, the SNMP routines will need
to be updated to handle the new indexing. Finally, the
ipIfStatsTable is optional and may be ignored.
The ipSystemStatsTable is effectively new, but it may be able to make use of most of the instrumentation from the old ipv6IfStatsTable. As with the IPv4 discussion, one implementation strategy would be to count the statistics for the ipIfStatsTable and aggregate them when queried for this table. Again, as with the IPv4 discussion, this strategy only works if the interfaces cannot be removed or if the statistics for removed interfaces are somehow retained.
The ipv6AddrPrefixTable is now the ipAddressPrefixTable. The new table contains an extra object and the additional index required for IPv4 compatibility. As above, the SNMP routines will need to be updated to handle the new indexing.
The ipAddressTable is loosely based on the ipv6AddrTable but has changed considerably with the addition of several new objects and the removal of one of its indexes.
The IPv6 routing information (ipv6RouteNumber, ipv6DiscardedRoutes, and ipv6RouteTable) has been removed from this MIB. The replacements or updates for this information is in the update to the IP Forwarding Table MIB [16]. The ipv6NetToMediaTable has been converted to the ipNetToPhysicalTable. The new table contains an extra object and the additional index required for IPv4 compatibility. As above, the SNMP routines will need to be updated to handle the new indexing.
The ICMP tables have been substantially changed. The previous tables required counting on a per-message and per-interface basis. The new tables only require counting on a per-message, per-protocol basis and include an aggregate of all messages on a per-protocol basis.
In addition to the above, several new tables have been added. Both the ipv6ScopeZoneIndexTable and ipDefaultRouterTable are required on all IPv6 entities. The ipv6RouterAdvertTable is only required on IPv6 routers.
The following MIB module imports from the IF-MIB [6] and the INET- ADDRESS-MIB [7] and references Neighbor Discovery [4], the IPv6 Stateless Address Autoconfiguration protocol [5], the Default Router Preferences document [8], ARP [10] and the IPv6 address architecture document [17].
IP-MIB DEFINITIONS ::= BEGIN
zeroDotZero FROM SNMPv2-SMI
PhysAddress, TruthValue,
TimeStamp, RowPointer,
TEXTUAL-CONVENTION, TestAndIncr,
RowStatus, StorageType FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF
InetAddress, InetAddressType,
InetAddressPrefixLength,
InetVersion, InetZoneIndex FROM INET-ADDRESS-MIB
InterfaceIndex FROM IF-MIB;
Shawn A. Routhier
Interworking Labs
108 Whispering Pines Dr. Suite 235
Scotts Valley, CA 95066
USA
EMail: <sar@iwl.com>"
DESCRIPTION
"The MIB module for managing IP and ICMP implementations, but
excluding their management of IP routes.
Copyright © The Internet Society (2006). This version of this MIB module is part of RFC 4293; see the RFC itself for full legal notices."
REVISION "200602020000Z"
DESCRIPTION
"The IP version neutral revision with added IPv6 objects for
ND, default routers, and router advertisements. As well as
being the successor to RFC 2011, this MIB is also the
successor to RFCs 2465 and 2466. Published as RFC 4293."
REVISION "199411010000Z"
DESCRIPTION
"A separate MIB module (IP-MIB) for IP and ICMP management
objects. Published as RFC 2011."
REVISION "199103310000Z"
DESCRIPTION
"The initial revision of this MIB module was part of MIB-II,
which was published as RFC 1213."
::= { mib-2 48}
--
-- The textual conventions we define and use in this MIB.
--
IpAddressOriginTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The origin of the address.
manual(2) indicates that the address was manually configured to a specified address, e.g., by user configuration.
dhcp(4) indicates an address that was assigned to this system by a DHCP server.
linklayer(5) indicates an address created by IPv6 stateless
auto-configuration.
random(6) indicates an address chosen by the system at random, e.g., an IPv4 address within 169.254/16, or an RFC 3041 privacy address."
SYNTAX INTEGER {
other(1),
manual(2),
dhcp(4),
linklayer(5),
random(6)
}
IpAddressStatusTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The status of an address. Most of the states correspond to
states from the IPv6 Stateless Address Autoconfiguration
protocol.
The preferred(1) state indicates that this is a valid address that can appear as the destination or source address of a packet.
The deprecated(2) state indicates that this is a valid but deprecated address that should no longer be used as a source address in new communications, but packets addressed to such an address are processed as expected.
The invalid(3) state indicates that this isn't a valid address and it shouldn't appear as the destination or source address of a packet.
The inaccessible(4) state indicates that the address is not accessible because the interface to which this address is assigned is not operational.
The unknown(5) state indicates that the status cannot be determined for some reason.
The tentative(6) state indicates that the uniqueness of the address on the link is being verified. Addresses in this state should not be used for general communication and should only be used to determine the uniqueness of the address.
The duplicate(7) state indicates the address has been determined to be non-unique on the link and so must not be
used.
The optimistic(8) state indicates the address is available for use, subject to restrictions, while its uniqueness on a link is being verified.
In the absence of other information, an IPv4 address is
always preferred(1)."
REFERENCE "RFC 2462"
SYNTAX INTEGER {
preferred(1),
deprecated(2),
invalid(3),
inaccessible(4),
unknown(5),
tentative(6),
duplicate(7),
optimistic(8)
}
IpAddressPrefixOriginTC ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The origin of this prefix.
manual(2) indicates a prefix that was manually configured.
wellknown(3) indicates a well-known prefix, e.g., 169.254/16 for IPv4 auto-configuration or fe80::/10 for IPv6 link-local addresses. Well known prefixes may be assigned by IANA, the address registries, or by specification in a standards track RFC.
dhcp(4) indicates a prefix that was assigned by a DHCP server.
routeradv(5) indicates a prefix learned from a router advertisement.
Note: while IpAddressOriginTC and IpAddressPrefixOriginTC are similar, they are not identical. The first defines how an address was created, while the second defines how a prefix was found."
SYNTAX INTEGER {
other(1),
manual(2),
wellknown(3),
dhcp(4),
routeradv(5)
}
Ipv6AddressIfIdentifierTC ::= TEXTUAL-CONVENTION
DISPLAY-HINT "2x:"
STATUS current
DESCRIPTION
"This data type is used to model IPv6 address
interface identifiers. This is a binary string
of up to 8 octets in network byte-order."
SYNTAX OCTET STRING (SIZE (0..8))
--
-- the IP general group
-- some objects that affect all of IPv4
--
ip OBJECT IDENTIFIER ::= { mib-2 4 }
SYNTAX INTEGER {
forwarding(1), -- acting as a router
notForwarding(2) -- NOT acting as a router
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The indication of whether this entity is acting as an IPv4
router in respect to the forwarding of datagrams received
by, but not addressed to, this entity. IPv4 routers forward
datagrams. IPv4 hosts do not (except those source-routed
via the host).
When this object is written, the entity should save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system. Note: a stronger requirement is not used because this object was previously defined."
::= { ip 1 }
SYNTAX Integer32 (1..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value inserted into the Time-To-Live field of
the IPv4 header of datagrams originated at this entity,
whenever a TTL value is not supplied by the transport layer
protocol.
When this object is written, the entity should save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system. Note: a stronger requirement is not used because this object was previously defined."
::= { ip 2 }
SYNTAX Integer32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The maximum number of seconds that received fragments are
held while they are awaiting reassembly at this entity."
::= { ip 13 }
--
-- the IPv6 general group
-- Some objects that affect all of IPv6
--
SYNTAX INTEGER {
forwarding(1), -- acting as a router
notForwarding(2) -- NOT acting as a router
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The indication of whether this entity is acting as an IPv6
router on any interface in respect to the forwarding of
datagrams received by, but not addressed to, this entity.
IPv6 routers forward datagrams. IPv6 hosts do not (except
those source-routed via the host).
When this object is written, the entity SHOULD save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system."
::= { ip 25 }
SYNTAX Integer32 (0..255)
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The default value inserted into the Hop Limit field of the IPv6 header of datagrams originated at this entity whenever a Hop Limit value is not supplied by the transport layer protocol.
When this object is written, the entity SHOULD save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system." REFERENCE "RFC 2461 Section 6.3.2"
::= { ip 26 }
--
-- IPv4 Interface Table
--
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
a row in the ipv4InterfaceTable was added or deleted, or
when an ipv4InterfaceReasmMaxSize or an
ipv4InterfaceEnableStatus object was modified.
If new objects are added to the ipv4InterfaceTable that require the ipv4InterfaceTableLastChange to be updated when they are modified, they must specify that requirement in their description clause."
::= { ip 27 }
SYNTAX SEQUENCE OF Ipv4InterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table containing per-interface IPv4-specific
information."
::= { ip 28 }
SYNTAX Ipv4InterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing IPv4-specific information for a specific
interface."
INDEX { ipv4InterfaceIfIndex }
::= { ipv4InterfaceTable 1 }
Ipv4InterfaceEntry ::= SEQUENCE {
ipv4InterfaceIfIndex InterfaceIndex,
ipv4InterfaceReasmMaxSize Integer32,
ipv4InterfaceEnableStatus INTEGER,
ipv4InterfaceRetransmitTime Unsigned32
}
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
identified by the same value of the IF-MIB's ifIndex."
::= { ipv4InterfaceEntry 1 }
SYNTAX Integer32 (0..65535)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the largest IPv4 datagram that this entity can
re-assemble from incoming IPv4 fragmented datagrams received
on this interface."
::= { ipv4InterfaceEntry 2 }
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The indication of whether IPv4 is enabled (up) or disabled
(down) on this interface. This object does not affect the
state of the interface itself, only its connection to an
IPv4 stack. The IF-MIB should be used to control the state
of the interface."
::= { ipv4InterfaceEntry 3 }
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time between retransmissions of ARP requests to a
neighbor when resolving the address or when probing the
reachability of a neighbor."
REFERENCE "RFC 1122"
DEFVAL { 1000 }
::= { ipv4InterfaceEntry 4 }
--
-- v6 interface table
--
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
a row in the ipv6InterfaceTable was added or deleted or when
an ipv6InterfaceReasmMaxSize, ipv6InterfaceIdentifier,
ipv6InterfaceEnableStatus, ipv6InterfaceReachableTime,
ipv6InterfaceRetransmitTime, or ipv6InterfaceForwarding
object was modified.
If new objects are added to the ipv6InterfaceTable that require the ipv6InterfaceTableLastChange to be updated when they are modified, they must specify that requirement in their description clause."
::= { ip 29 }
SYNTAX SEQUENCE OF Ipv6InterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table containing per-interface IPv6-specific
information."
::= { ip 30 }
SYNTAX Ipv6InterfaceEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry containing IPv6-specific information for a given
interface."
INDEX { ipv6InterfaceIfIndex }
::= { ipv6InterfaceTable 1 }
Ipv6InterfaceEntry ::= SEQUENCE {
ipv6InterfaceIfIndex InterfaceIndex,
ipv6InterfaceReasmMaxSize Unsigned32,
ipv6InterfaceIdentifier Ipv6AddressIfIdentifierTC,
ipv6InterfaceEnableStatus INTEGER,
ipv6InterfaceReachableTime Unsigned32,
ipv6InterfaceRetransmitTime Unsigned32,
ipv6InterfaceForwarding INTEGER
}
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
identified by the same value of the IF-MIB's ifIndex."
::= { ipv6InterfaceEntry 1 }
SYNTAX Unsigned32 (1500..65535)
UNITS "octets"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The size of the largest IPv6 datagram that this entity can
re-assemble from incoming IPv6 fragmented datagrams received
on this interface."
::= { ipv6InterfaceEntry 2 }
SYNTAX Ipv6AddressIfIdentifierTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The Interface Identifier for this interface. The Interface
Identifier is combined with an address prefix to form an
interface address.
By default, the Interface Identifier is auto-configured according to the rules of the link type to which this interface is attached.
A zero length identifier may be used where appropriate. One possible example is a loopback interface."
::= { ipv6InterfaceEntry 3 }
-- This object ID is reserved as it was used in earlier versions of
-- the MIB module. In theory, OIDs are not assigned until the
-- specification is released as an RFC; however, as some companies
-- may have shipped code based on earlier versions of the MIB, it
-- seems best to reserve this OID. This OID had been
-- ipv6InterfacePhysicalAddress.
-- ::= { ipv6InterfaceEntry 4}
SYNTAX INTEGER {
up(1),
down(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The indication of whether IPv6 is enabled (up) or disabled
(down) on this interface. This object does not affect the
state of the interface itself, only its connection to an
IPv6 stack. The IF-MIB should be used to control the state
of the interface.
When this object is written, the entity SHOULD save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system."
::= { ipv6InterfaceEntry 5 }
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time a neighbor is considered reachable after receiving
a reachability confirmation."
REFERENCE "RFC 2461, Section 6.3.2"
::= { ipv6InterfaceEntry 6 }
SYNTAX Unsigned32
UNITS "milliseconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The time between retransmissions of Neighbor Solicitation
messages to a neighbor when resolving the address or when
probing the reachability of a neighbor."
REFERENCE "RFC 2461, Section 6.3.2"
::= { ipv6InterfaceEntry 7 }
SYNTAX INTEGER {
forwarding(1), -- acting as a router
notForwarding(2) -- NOT acting as a router
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The indication of whether this entity is acting as an IPv6
router on this interface with respect to the forwarding of
datagrams received by, but not addressed to, this entity.
IPv6 routers forward datagrams. IPv6 hosts do not (except
those source-routed via the host).
This object is constrained by ipv6IpForwarding and is ignored if ipv6IpForwarding is set to notForwarding. Those systems that do not provide per-interface control of the forwarding function should set this object to forwarding for all interfaces and allow the ipv6IpForwarding object to control the forwarding capability.
When this object is written, the entity SHOULD save the change to non-volatile storage and restore the object from non-volatile storage upon re-initialization of the system."
::= { ipv6InterfaceEntry 8 }
--
-- Per-Interface or System-Wide IP statistics.
--
-- The following two tables, ipSystemStatsTable and ipIfStatsTable,
-- are intended to provide the same counters at different granularities.
-- The ipSystemStatsTable provides system wide counters aggregating
-- the traffic counters for all interfaces for a given address type.
-- The ipIfStatsTable provides the same counters but for specific
-- interfaces rather than as an aggregate.
--
-- Note well: If a system provides both system-wide and interface-
-- specific values, the system-wide value may not be equal to the sum
-- of the interface-specific values across all interfaces due to e.g.,
-- dynamic interface creation/deletion.
--
-- Note well: Both of these tables contain some items that are
-- represented by two objects, representing the value in either 32
-- or 64 bits. For those objects, the 32-bit value MUST be the low
-- order 32 bits of the 64-bit value. Also note that the 32-bit
-- counters must be included when the 64-bit counters are included.
ipTrafficStats OBJECT IDENTIFIER ::= { ip 31 }
SYNTAX SEQUENCE OF IpSystemStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table containing system wide, IP version specific
traffic statistics. This table and the ipIfStatsTable
contain similar objects whose difference is in their
granularity. Where this table contains system wide traffic
statistics, the ipIfStatsTable contains the same statistics
but counted on a per-interface basis."
::= { ipTrafficStats 1 }
SYNTAX IpSystemStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A statistics entry containing system-wide objects for a
particular IP version."
INDEX { ipSystemStatsIPVersion }
::= { ipSystemStatsTable 1 }
IpSystemStatsEntry ::= SEQUENCE {
ipSystemStatsIPVersion InetVersion,
ipSystemStatsInReceives Counter32,
ipSystemStatsHCInReceives Counter64,
ipSystemStatsInOctets Counter32,
ipSystemStatsHCInOctets Counter64,
ipSystemStatsInHdrErrors Counter32,
ipSystemStatsInNoRoutes Counter32,
ipSystemStatsInAddrErrors Counter32,
ipSystemStatsInUnknownProtos Counter32,
ipSystemStatsInTruncatedPkts Counter32,
ipSystemStatsInForwDatagrams Counter32,
ipSystemStatsHCInForwDatagrams Counter64,
ipSystemStatsReasmReqds Counter32,
ipSystemStatsReasmOKs Counter32,
ipSystemStatsReasmFails Counter32,
ipSystemStatsInDiscards Counter32,
ipSystemStatsInDelivers Counter32,
ipSystemStatsHCInDelivers Counter64,
ipSystemStatsOutRequests Counter32,
ipSystemStatsHCOutRequests Counter64,
ipSystemStatsOutNoRoutes Counter32,
ipSystemStatsOutForwDatagrams Counter32,
ipSystemStatsHCOutForwDatagrams Counter64,
ipSystemStatsOutDiscards Counter32,
ipSystemStatsOutFragReqds Counter32,
ipSystemStatsOutFragOKs Counter32,
ipSystemStatsOutFragFails Counter32,
ipSystemStatsOutFragCreates Counter32,
ipSystemStatsOutTransmits Counter32,
ipSystemStatsHCOutTransmits Counter64,
ipSystemStatsOutOctets Counter32,
ipSystemStatsHCOutOctets Counter64,
ipSystemStatsInMcastPkts Counter32,
ipSystemStatsHCInMcastPkts Counter64,
ipSystemStatsInMcastOctets Counter32,
ipSystemStatsHCInMcastOctets Counter64,
ipSystemStatsOutMcastPkts Counter32,
ipSystemStatsHCOutMcastPkts Counter64,
ipSystemStatsOutMcastOctets Counter32,
ipSystemStatsHCOutMcastOctets Counter64,
ipSystemStatsInBcastPkts Counter32,
ipSystemStatsHCInBcastPkts Counter64,
ipSystemStatsOutBcastPkts Counter32,
ipSystemStatsHCOutBcastPkts Counter64,
ipSystemStatsDiscontinuityTime TimeStamp,
ipSystemStatsRefreshRate Unsigned32
}
SYNTAX InetVersion
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP version of this row."
::= { ipSystemStatsEntry 1 }
-- This object ID is reserved to allow the IDs for this table's objects
-- to align with the objects in the ipIfStatsTable.
-- ::= { ipSystemStatsEntry 2 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of input IP datagrams received, including those received in error.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 3 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of input IP datagrams received, including
those received in error. This object counts the same
datagrams as ipSystemStatsInReceives, but allows for larger
values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 4 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in input IP datagrams,
including those received in error. Octets from datagrams
counted in ipSystemStatsInReceives MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 5 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in input IP datagrams,
including those received in error. This object counts the
same octets as ipSystemStatsInOctets, but allows for larger
values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 6 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded due to errors in
their IP headers, including version number mismatch, other
format errors, hop count exceeded, errors discovered in
processing their IP options, etc.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 7 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because no route
could be found to transmit them to their destination.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 8 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because the IP
address in their IP header's destination field was not a
valid address to be received at this entity. This count
includes invalid addresses (e.g., ::0). For entities
that are not IP routers and therefore do not forward
datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 9 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of locally-addressed IP datagrams received
successfully but discarded because of an unknown or
unsupported protocol.
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 10 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because the
datagram frame didn't carry enough data.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 11 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input datagrams for which this entity was not their final IP destination and for which this entity attempted to find a route to forward them to that final destination. In entities that do not act as IP routers, this counter will include only those datagrams that were Source-Routed via this entity, and the Source-Route processing was successful.
When tracking interface statistics, the counter of the incoming interface is incremented for each datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 12 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input datagrams for which this entity was not
their final IP destination and for which this entity
attempted to find a route to forward them to that final
destination. This object counts the same packets as
ipSystemStatsInForwDatagrams, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 13 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP fragments received that needed to be
reassembled at this interface.
When tracking interface statistics, the counter of the interface to which these fragments were addressed is incremented. This interface might not be the same as the input interface for some of the fragments.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 14 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams successfully reassembled.
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 15 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of failures detected by the IP re-assembly
algorithm (for whatever reason: timed out, errors, etc.).
Note that this is not necessarily a count of discarded IP
fragments since some algorithms (notably the algorithm in
RFC 815) can lose track of the number of fragments by
combining them as they are received.
When tracking interface statistics, the counter of the interface to which these fragments were addressed is incremented. This interface might not be the same as the input interface for some of the fragments.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 16 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams for which no problems were
encountered to prevent their continued processing, but
were discarded (e.g., for lack of buffer space). Note that
this counter does not include any datagrams discarded while
awaiting re-assembly.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 17 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of datagrams successfully delivered to IP
user-protocols (including ICMP).
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 18 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of datagrams successfully delivered to IP
user-protocols (including ICMP). This object counts the
same packets as ipSystemStatsInDelivers, but allows for
larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 19 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. Note that this counter does not include any
datagrams counted in ipSystemStatsOutForwDatagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 20 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. This object counts the same packets as
ipSystemStatsOutRequests, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 21 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of locally generated IP datagrams discarded
because no route could be found to transmit them to their
destination.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 22 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of datagrams for which this entity was not their
final IP destination and for which it was successful in
finding a path to their final destination. In entities
that do not act as IP routers, this counter will include
only those datagrams that were Source-Routed via this
entity, and the Source-Route processing was successful.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully forwarded datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 23 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of datagrams for which this entity was not their
final IP destination and for which it was successful in
finding a path to their final destination. This object
counts the same packets as ipSystemStatsOutForwDatagrams,
but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 24 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output IP datagrams for which no problem was
encountered to prevent their transmission to their
destination, but were discarded (e.g., for lack of
buffer space). Note that this counter would include
datagrams counted in ipSystemStatsOutForwDatagrams if any such datagrams met this (discretionary) discard criterion.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 25 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that would require fragmentation
in order to be transmitted.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 26 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been successfully
fragmented.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 27 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been discarded because
they needed to be fragmented but could not be. This
includes IPv4 packets that have the DF bit set and IPv6
packets that are being forwarded and exceed the outgoing
link MTU.
When tracking interface statistics, the counter of the outgoing interface is incremented for an unsuccessfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 28 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output datagram fragments that have been
generated as a result of IP fragmentation.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 29 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that this entity supplied
to the lower layers for transmission. This includes
datagrams generated locally and those forwarded by this
entity.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 30 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that this entity supplied
to the lower layers for transmission. This object counts
the same datagrams as ipSystemStatsOutTransmits, but allows
for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 31 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. Octets from datagrams
counted in ipSystemStatsOutTransmits MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 32 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. This objects counts the same
octets as ipSystemStatsOutOctets, but allows for larger
values.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 33 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams received.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 34 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams received. This object
counts the same datagrams as ipSystemStatsInMcastPkts but
allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 35 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in IP multicast
datagrams. Octets from datagrams counted in
ipSystemStatsInMcastPkts MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 36 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in IP multicast
datagrams. This object counts the same octets as
ipSystemStatsInMcastOctets, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 37 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams transmitted.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 38 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams transmitted. This
object counts the same datagrams as
ipSystemStatsOutMcastPkts, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 39 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets transmitted in IP multicast
datagrams. Octets from datagrams counted in
ipSystemStatsOutMcastPkts MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 40 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets transmitted in IP multicast
datagrams. This object counts the same octets as
ipSystemStatsOutMcastOctets, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 41 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams received.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 42 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams received. This object
counts the same datagrams as ipSystemStatsInBcastPkts but
allows for larger values.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 43 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams transmitted.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 44 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams transmitted. This
object counts the same datagrams as
ipSystemStatsOutBcastPkts, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipSystemStatsDiscontinuityTime."
::= { ipSystemStatsEntry 45 }
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
any one or more of this entry's counters suffered a
discontinuity.
If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value."
::= { ipSystemStatsEntry 46 }
SYNTAX Unsigned32
UNITS "milli-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum reasonable polling interval for this entry.
This object provides an indication of the minimum amount of
time required to update the counters in this entry."
::= { ipSystemStatsEntry 47 }
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
a row in the ipIfStatsTable was added or deleted.
If new objects are added to the ipIfStatsTable that require the ipIfStatsTableLastChange to be updated when they are modified, they must specify that requirement in their description clause."
::= { ipTrafficStats 2 }
SYNTAX SEQUENCE OF IpIfStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The table containing per-interface traffic statistics. This
table and the ipSystemStatsTable contain similar objects
whose difference is in their granularity. Where this table
contains per-interface statistics, the ipSystemStatsTable
contains the same statistics, but counted on a system wide
basis."
::= { ipTrafficStats 3 }
SYNTAX IpIfStatsEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An interface statistics entry containing objects for a
particular interface and version of IP."
INDEX { ipIfStatsIPVersion, ipIfStatsIfIndex }
::= { ipIfStatsTable 1 }
IpIfStatsEntry ::= SEQUENCE {
ipIfStatsIPVersion InetVersion,
ipIfStatsIfIndex InterfaceIndex,
ipIfStatsInReceives Counter32,
ipIfStatsHCInReceives Counter64,
ipIfStatsInOctets Counter32,
ipIfStatsHCInOctets Counter64,
ipIfStatsInHdrErrors Counter32,
ipIfStatsInNoRoutes Counter32,
ipIfStatsInAddrErrors Counter32,
ipIfStatsInUnknownProtos Counter32,
ipIfStatsInTruncatedPkts Counter32,
ipIfStatsInForwDatagrams Counter32,
ipIfStatsHCInForwDatagrams Counter64,
ipIfStatsReasmReqds Counter32,
ipIfStatsReasmOKs Counter32,
ipIfStatsReasmFails Counter32,
ipIfStatsInDiscards Counter32,
ipIfStatsInDelivers Counter32,
ipIfStatsHCInDelivers Counter64,
ipIfStatsOutRequests Counter32,
ipIfStatsHCOutRequests Counter64,
ipIfStatsOutForwDatagrams Counter32,
ipIfStatsHCOutForwDatagrams Counter64,
ipIfStatsOutDiscards Counter32,
ipIfStatsOutFragReqds Counter32,
ipIfStatsOutFragOKs Counter32,
ipIfStatsOutFragFails Counter32,
ipIfStatsOutFragCreates Counter32,
ipIfStatsOutTransmits Counter32,
ipIfStatsHCOutTransmits Counter64,
ipIfStatsOutOctets Counter32,
ipIfStatsHCOutOctets Counter64,
ipIfStatsInMcastPkts Counter32,
ipIfStatsHCInMcastPkts Counter64,
ipIfStatsInMcastOctets Counter32,
ipIfStatsHCInMcastOctets Counter64,
ipIfStatsOutMcastPkts Counter32,
ipIfStatsHCOutMcastPkts Counter64,
ipIfStatsOutMcastOctets Counter32,
ipIfStatsHCOutMcastOctets Counter64,
ipIfStatsInBcastPkts Counter32,
ipIfStatsHCInBcastPkts Counter64,
ipIfStatsOutBcastPkts Counter32,
ipIfStatsHCOutBcastPkts Counter64,
ipIfStatsDiscontinuityTime TimeStamp,
ipIfStatsRefreshRate Unsigned32
}
SYNTAX InetVersion
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The IP version of this row."
::= { ipIfStatsEntry 1 }
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the interface to
which this entry is applicable. The interface identified by
a particular value of this index is the same interface as
identified by the same value of the IF-MIB's ifIndex."
::= { ipIfStatsEntry 2 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of input IP datagrams received, including
those received in error.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 3 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of input IP datagrams received, including
those received in error. This object counts the same
datagrams as ipIfStatsInReceives, but allows for larger
values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 4 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in input IP datagrams,
including those received in error. Octets from datagrams
counted in ipIfStatsInReceives MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 5 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in input IP datagrams,
including those received in error. This object counts the
same octets as ipIfStatsInOctets, but allows for larger
values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 6 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded due to errors in
their IP headers, including version number mismatch, other
format errors, hop count exceeded, errors discovered in
processing their IP options, etc.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 7 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because no route
could be found to transmit them to their destination.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 8 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because the IP
address in their IP header's destination field was not a
valid address to be received at this entity. This count
includes invalid addresses (e.g., ::0). For entities that
are not IP routers and therefore do not forward datagrams,
this counter includes datagrams discarded because the
destination address was not a local address.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 9 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of locally-addressed IP datagrams received
successfully but discarded because of an unknown or
unsupported protocol.
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 10 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams discarded because the
datagram frame didn't carry enough data.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 11 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input datagrams for which this entity was not
their final IP destination and for which this entity
attempted to find a route to forward them to that final
destination. In entities that do not act as IP routers,
this counter will include only those datagrams that were
Source-Routed via this entity, and the Source-Route
processing was successful.
When tracking interface statistics, the counter of the incoming interface is incremented for each datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 12 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input datagrams for which this entity was not
their final IP destination and for which this entity
attempted to find a route to forward them to that final
destination. This object counts the same packets as
ipIfStatsInForwDatagrams, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 13 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP fragments received that needed to be
reassembled at this interface.
When tracking interface statistics, the counter of the interface to which these fragments were addressed is incremented. This interface might not be the same as the input interface for some of the fragments.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 14 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams successfully reassembled.
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 15 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of failures detected by the IP re-assembly
algorithm (for whatever reason: timed out, errors, etc.).
Note that this is not necessarily a count of discarded IP
fragments since some algorithms (notably the algorithm in
RFC 815) can lose track of the number of fragments by
combining them as they are received.
When tracking interface statistics, the counter of the interface to which these fragments were addressed is incremented. This interface might not be the same as the input interface for some of the fragments.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 16 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of input IP datagrams for which no problems were
encountered to prevent their continued processing, but
were discarded (e.g., for lack of buffer space). Note that
this counter does not include any datagrams discarded while
awaiting re-assembly.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 17 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of datagrams successfully delivered to IP
user-protocols (including ICMP).
When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the
input interface for some of the datagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 18 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of datagrams successfully delivered to IP
user-protocols (including ICMP). This object counts the
same packets as ipIfStatsInDelivers, but allows for larger
values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 19 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. Note that this counter does not include any
datagrams counted in ipIfStatsOutForwDatagrams.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 20 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that local IP user-
protocols (including ICMP) supplied to IP in requests for
transmission. This object counts the same packets as
ipIfStatsOutRequests, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 21 }
-- This object ID is reserved to allow the IDs for this table's objects
-- to align with the objects in the ipSystemStatsTable.
-- ::= {ipIfStatsEntry 22}
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of datagrams for which this entity was not their
final IP destination and for which it was successful in
finding a path to their final destination. In entities
that do not act as IP routers, this counter will include
only those datagrams that were Source-Routed via this
entity, and the Source-Route processing was successful.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully forwarded datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 23 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of datagrams for which this entity was not their
final IP destination and for which it was successful in
finding a path to their final destination. This object
counts the same packets as ipIfStatsOutForwDatagrams, but
allows for larger values.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 24 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output IP datagrams for which no problem was
encountered to prevent their transmission to their
destination, but were discarded (e.g., for lack of
buffer space). Note that this counter would include
datagrams counted in ipIfStatsOutForwDatagrams if any such
datagrams met this (discretionary) discard criterion.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 25 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that would require fragmentation
in order to be transmitted.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 26 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been successfully
fragmented.
When tracking interface statistics, the counter of the
outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 27 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP datagrams that have been discarded because
they needed to be fragmented but could not be. This
includes IPv4 packets that have the DF bit set and IPv6
packets that are being forwarded and exceed the outgoing
link MTU.
When tracking interface statistics, the counter of the outgoing interface is incremented for an unsuccessfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 28 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of output datagram fragments that have been
generated as a result of IP fragmentation.
When tracking interface statistics, the counter of the outgoing interface is incremented for a successfully fragmented datagram.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 29 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that this entity supplied
to the lower layers for transmission. This includes
datagrams generated locally and those forwarded by this
entity.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 30 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of IP datagrams that this entity supplied
to the lower layers for transmission. This object counts
the same datagrams as ipIfStatsOutTransmits, but allows for
larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 31 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. Octets from datagrams
counted in ipIfStatsOutTransmits MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 32 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets in IP datagrams delivered to the
lower layers for transmission. This objects counts the same
octets as ipIfStatsOutOctets, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 33 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams received.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 34 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams received. This object
counts the same datagrams as ipIfStatsInMcastPkts, but
allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 35 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in IP multicast
datagrams. Octets from datagrams counted in
ipIfStatsInMcastPkts MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 36 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets received in IP multicast
datagrams. This object counts the same octets as
ipIfStatsInMcastOctets, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 37 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams transmitted.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 38 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP multicast datagrams transmitted. This
object counts the same datagrams as ipIfStatsOutMcastPkts,
but allows for larger values.
Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 39 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets transmitted in IP multicast
datagrams. Octets from datagrams counted in
ipIfStatsOutMcastPkts MUST be counted here.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 40 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The total number of octets transmitted in IP multicast
datagrams. This object counts the same octets as
ipIfStatsOutMcastOctets, but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 41 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams received.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 42 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams received. This object
counts the same datagrams as ipIfStatsInBcastPkts, but
allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 43 }
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams transmitted.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 44 }
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of IP broadcast datagrams transmitted. This
object counts the same datagrams as ipIfStatsOutBcastPkts,
but allows for larger values.
Discontinuities in the value of this counter can occur at
re-initialization of the management system, and at other
times as indicated by the value of
ipIfStatsDiscontinuityTime."
::= { ipIfStatsEntry 45 }
SYNTAX TimeStamp
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of sysUpTime on the most recent occasion at which
any one or more of this entry's counters suffered a discontinuity.
If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value."
::= { ipIfStatsEntry 46 }
SYNTAX Unsigned32
UNITS "milli-seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The minimum reasonable polling interval for this entry.
This object provides an indication of the minimum amount of
time required to update the counters in this entry."
::= { ipIfStatsEntry 47 }
--
-- Internet Address Prefix table
--
SYNTAX SEQUENCE OF IpAddressPrefixEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table allows the user to determine the source of an IP
address or set of IP addresses, and allows other tables to
share the information via pointer rather than by copying.
For example, when the node configures both a unicast and anycast address for a prefix, the ipAddressPrefix objects for those addresses will point to a single row in this table.
This table primarily provides support for IPv6 prefixes, and several of the objects are less meaningful for IPv4. The table continues to allow IPv4 addresses to allow future flexibility. In order to promote a common configuration, this document includes suggestions for default values for IPv4 prefixes. Each of these values may be overridden if an object is meaningful to the node.
All prefixes used by this entity should be included in this table independent of how the entity learned the prefix. (This table isn't limited to prefixes learned from router
advertisements.)"
::= { ip 32 }
SYNTAX IpAddressPrefixEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the ipAddressPrefixTable."
INDEX { ipAddressPrefixIfIndex, ipAddressPrefixType,
ipAddressPrefixPrefix, ipAddressPrefixLength }
::= { ipAddressPrefixTable 1 }
IpAddressPrefixEntry ::= SEQUENCE {
ipAddressPrefixIfIndex InterfaceIndex,
ipAddressPrefixType InetAddressType,
ipAddressPrefixPrefix InetAddress,
ipAddressPrefixLength InetAddressPrefixLength,
ipAddressPrefixOrigin IpAddressPrefixOriginTC,
ipAddressPrefixOnLinkFlag TruthValue,
ipAddressPrefixAutonomousFlag TruthValue,
ipAddressPrefixAdvPreferredLifetime Unsigned32,
ipAddressPrefixAdvValidLifetime Unsigned32
}
SYNTAX InterfaceIndex
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The index value that uniquely identifies the interface on
which this prefix is configured. The interface identified
by a particular value of this index is the same interface as
identified by the same value of the IF-MIB's ifIndex."
::= { ipAddressPrefixEntry 1 }
SYNTAX InetAddressType
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address type of ipAddressPrefix."
::= { ipAddressPrefixEntry 2 }
SYNTAX InetAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The address prefix. The address type of this object is
specified in ipAddressPrefixType. The length of this object
is the standard length for objects of that type (4 or 16
bytes). Any bits after ipAddressPrefixLength must be zero.
Implementors need to be aware that, if the size of ipAddressPrefixPrefix exceeds 114 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3."
::= { ipAddressPrefixEntry 3 }
SYNTAX InetAddressPrefixLength
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The prefix length associated with this prefix.
The value 0 has no special meaning for this object. It simply refers to address '::/0'."
::= { ipAddressPrefixEntry 4 }
SYNTAX IpAddressPrefixOriginTC
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The origin of this prefix."
::= { ipAddressPrefixEntry 5 }
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object has the value 'true(1)', if this prefix can be
used for on-link determination; otherwise, the value is
'false(2)'.
The default for IPv4 prefixes is 'true(1)'."
REFERENCE "For IPv6 RFC 2461, especially sections 2 and 4.6.2 and
RFC 2462"
::= { ipAddressPrefixEntry 6 }
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Autonomous address configuration flag. When true(1),
indicates that this