|
Network Working Group Request for Comments: 3555 Category: Standards Track |
S. Casner Packet Design P. Hoschka W3C/INRIA/MIT July 2003 |
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
Copyright © The Internet Society (2003). All Rights Reserved.
This document defines the procedure to register RTP Payload Formats as audio, video or other MIME subtype names. This is useful in a text-based format or control protocol to identify the type of an RTP transmission. This document also registers all the RTP payload formats defined in the RTP Profile for Audio and Video Conferences as MIME subtypes. Some of these may also be used for transfer modes other than RTP.
1. Introduction
1.1. IANA Considerations
1.2. Terminology
2. Procedure For Registering MIME Types for RTP Payload Types
3. Mapping to SDP Parameters
4. Registrations for "Audio/Video Profile"
4.1. Audio Type Registrations
4.2. Video Type Registrations
5. Security Considerations
6. Normative References
7. Authors' Addresses
8. Full Copyright Statement
The MIME registration procedure described in RFC 2048 [1] was originally designed for transport of multimedia information via asynchronous Internet mail, but the MIME namespace now provides identification for other transport modes as well. This document defines the procedure to register MIME subtype names for use with the Real-time Transport Protocol (RTP), RFC 3550 [2], to identify RTP payload formats.
This document also registers all the RTP payload formats defined in the RTP Profile for Audio and Video Conferences, RFC 3551 [3], as MIME subtypes under the "audio" and "video" MIME types.
This document registers the following MIME subtypes:
audio/DVI4
audio/G722
audio/G723
audio/G726-16
audio/G726-24
audio/G726-32
audio/G726-40
audio/G728
audio/G729
audio/G729D
audio/G729E
audio/GSM
audio/GSM-EFR
audio/L8
audio/L16
audio/LPC
audio/MPA
audio/PCMA
audio/PCMU
audio/QCELP
audio/RED
audio/VDVI
video/BT656
video/CelB
video/JPEG
video/H261
video/H263
video/H263-1998
video/H263-2000
video/MPV
video/MP2T
video/MP1S
video/MP2P
video/BMPEG
video/nv
MIME subtype audio/L16 has already been registered via RFC 2586 for transports other than RTP. That registration is incorporated here and augmented with additional information for RTP transport.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in RFC 2119 [4] and indicate requirement levels for implementations compliant with this specification.
Registering an RTP payload type as a MIME type follows the same procedures as described in RFC 2048 and uses the registration template shown in Section 2.8 of RFC 2048. Some additional parameters are required to specify how a particular payload format is transported over RTP:
Published specification
A description of the encoding and a specification of the
payload format must be provided, usually by reference to an RTP
payload format specification RFC. That RFC may be separate, or
the MIME subtype registration may be incorporated into the
payload format specification RFC. The payload format
specification MUST include the RTP timestamp clock rate (or
multiple rates for audio encodings with multiple sampling
rates).
A reference to a further description of the data compression format itself should be provided, if available.
Required parameters
If the payload format does not have a fixed RTP timestamp clock
rate, then a "rate" parameter is required to specify the RTP
timestamp clock rate. A particular payload format may have
additional required parameters.
Optional parameters
Most audio payload formats can have an optional "channels"
parameter to specify the number of audio channels included in
the transmission. Any payload format, but most likely audio
formats, may also include the optional parameters "ptime", to
specify the recommended length of time in milliseconds
represented by the media in a packet, and/or "maxptime" to
specify the maximum amount of media which can be encapsulated
in each packet, expressed as time in milliseconds. The "ptime"
and "maxptime" parameters are defined in the Session
Description Protocol (SDP) [5].
A particular payload format may have additional optional parameters.
Encoding considerations
The fact that the type can be transferred via RTP MUST be
noted.
Depending on whether the type has already been registered for transfer with a non-RTP protocol (e.g. MIME mail or http) or not, several different cases can occur:
a) Not yet registered as a MIME type
A new registration should be constructed using the MIME registration template. The registration may specify transfer via other means in addition to RTP if that is feasible and desired. The encoding considerations must specify how the type is transferred via RTP.
Optional parameters may be defined as needed, and it must be clearly stated whether to which mode(s) of transfer the parameters apply.
b) MIME type exists for a non-RTP protocol
The encoding considerations of the existing type should be changed to indicate that the type can also be transferred via RTP.
RTP-specific parameters may be added, and it must be clearly stated that these are only to be used when the media type is transmitted via RTP transport.
c) Update an existing MIME type for RTP to be used for a non-RTP protocol
The encoding considerations of the existing type should be changed to indicate that the type can also be transferred via a non-RTP protocol (e.g. SMTP, HTTP).
Non-RTP-specific parameters can be added, and it must be clearly stated that these are only to be used when the media type is transmitted via a non-RTP transport.
The representation of a MIME media type is specified in the syntax of the Content-Type header field in RFC 2045 [6] as follows:
type "/" subtype *(";" parameter)
Parameters may be required for a particular type or subtype or they may be optional. For media types which represent RTP payload formats, the parameters "rate", "channels", "ptime", and "maxptime" have general definitions (given above) that may apply across types and subtypes. The format for a parameter is specified in RFC 2045 as
attribute "=" value
where attribute is the parameter name and the permissible values are specified for each parameter. The value may need to be a quoted string if it contains any of the special characters listed in RFC 2045.
The information carried in the media type string has a specific mapping to fields in the Session Description Protocol (SDP) [5], which is commonly used to describe RTP sessions. The mapping is as follows:
An example mapping is as follows:
audio/L16; rate=48000; channels=2; ptime=5; emphasis=50-15
m=audio 49170 RTP/AVP 97
a=rtpmap:97 L16/48000/2
a=fmtp:97 emphasis=50-15
a=ptime:5
Note that the payload format (encoding) names defined in the RTP Profile are commonly shown in upper case. MIME subtypes are commonly shown in lower case. These names are case-insensitive in both places. Similarly, parameter names are case-insensitive both in MIME types and in the default mapping to the SDP a=fmtp attribute.
In the following sections, all RTP payload formats described in the RTP Profile for Audio and Video Conferences, RFC 3551 [3], are registered as MIME subtypes.
The following sections register all of the RTP audio payload types defined in RFC 3551 as MIME types.
For most audio payload formats, the RTP timestamp clock rate is equal to the sampling rate. Some payload formats operate only at one fixed sampling rate, while others are adjustable.
MIME media type name: audio
MIME subtype name: DVI4
Required parameters: rate
The RTP timestamp clock rate, which is equal to the sampling
rate. The typical rate is 8000, but other rates may be
specified.
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G722
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G723
Required parameters: None
Optional parameters:
ptime, maxptime
bitrate: the data rate in kb/s used or preferred for the audio
bit stream, with permissible values 5.3 or 6.3. If
unspecified, the bitrate may change from frame to frame as
indicated inband.
annexa: indicates that Annex A, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G726-16
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G726-24
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G726-32
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G726-40
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G728
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G729
Required parameters: None
Optional parameters:
ptime, maxptime
annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G729D
Required parameters: None
Optional parameters:
ptime, maxptime
annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: G729E
Required parameters: None
Optional parameters:
ptime, maxptime
annexb: indicates that Annex B, voice activity detection, is used or preferred. Permissible values are "yes" and "no" (without the quotes); "yes" is implied if this parameter is omitted.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: GSM
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: GSM-EFR
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: L8
Required parameters: rate, the RTP timestamp clock rate
Optional parameters: channels, ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME subtype audio/L16 has already been registered via RFC 2586 for transports other than RTP. That registration is incorporated here and augmented with additional information for RTP transport.
MIME media type name: audio
MIME subtype name: L16
Required parameters
rate: number of samples per second -- For non-RTP transport,
the permissible values for rate are 8000, 11025, 16000, 22050,
24000, 32000, 44100, and 48000 samples per second. For RTP
transport, other values are permissible but the aforementioned
values are RECOMMENDED. For RTP, the rate parameter indicates
the RTP timestamp clock rate, which is equal to the sample
rate.
Optional parameters
channels: how many audio streams are interleaved -- defaults
to 1; stereo would be 2, etc. Interleaving takes place
between individual two-byte samples.
emphasis: analog preemphasis applied to the signal before quantization. The only emphasis value defined here is emphasis=50-15 to indicate the 50/15 microsecond preemphasis used with Compact Disks. This parameter MUST be omitted if no analog preemphasis was applied.
channel-order: specifies the sample interleaving order for
multiple-channel audio streams (see [7] Section 7).
Permissible values are DV.LRLsRs, DV.LRCS, DV.LRCWo,
DV.LRLsRsC, DV.LRLsRsCS, DV.LmixRmixTWoQ1Q2,
DV.LRCWoLsRsLmixRmix, DV.LRCWoLs1Rs1Ls2Rs2, DV.LRCWoLsRsLcRc.
For interoperation with DV video systems, only a subset of
these channel combinations is specified for use with 20-bit
linear encoding in the DV video specification [4]; those are
DV.LRLsRs, DV.LRCS, DV.LmixRmixTWoQ1Q2. This parameter MUST
be omitted when the AIFF-C channel order convention (see RFC
3551) is in use.
For RTP, ptime: RECOMMENDED duration of each packet in milliseconds.
For RTP, maxptime: maximum duration of each packet in milliseconds.
Encoding considerations
Audio data is binary data, and must be encoded for non-binary
transport; the Base64 encoding is suitable for Email. Note
that audio data does not compress easily using lossless
compression.
This type is also defined for transfer via RTP [RFC 3550].
Security considerations
Audio data is believed to offer no security risks.
See Section 5 of RFC 3555.
Interoperability considerations
This type is compatible with the encoding used in the WAV
(Microsoft Windows RIFF) and Apple AIFF union types, and with
the public domain "sox" and "rateconv" programs.
Published specification
RFC 2586 for non-RTP transports, RFC 3551 for RTP
Applications which use this media
The public domain "sox" and "rateconv" programs accept this
type.
Person to contact for further information
Intended usage
Common
It is expected that many audio and speech applications will use this type. Already the most popular platforms provide this type with the rate=11025 parameter referred to as "radio quality speech."
Author/Change controller
James Salsman for non-RTP transports.
Stephen Casner for RTP transport.
MIME media type name: audio
MIME subtype name: LPC
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: MPA (MPEG audio)
Required parameters: None
Optional parameters:
layer: which layer of MPEG audio encoding; permissible values
are 1, 2, 3.
samplerate: the rate at which audio is sampled. MPEG-1 audio supports sampling rates of 32, 44.1, and 48 kHz; MPEG-2 supports sampling rates of 16, 22.05 and 24 kHz. This parameter is separate from the RTP timestamp clock rate which is always 90000 Hz for MPA.
mode: permissible values are "stereo", "joint_stereo", "single_channel", "dual_channel". The "channels" parameter does not apply to MPA. It is undefined to put a number of channels in the SDP rtpmap attribute for MPA.
bitrate: the data rate for the audio bit stream.
ptime: RECOMMENDED duration of each packet in milliseconds.
maxptime: maximum duration of each packet in milliseconds.
Parameters which are omitted are left to the encoder to choose based on the session bandwidth, configuration information, or other constraints. The selected layer as well as the sampling rate and mode are indicated in the payload so receivers can process the data without these parameters being specified externally.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: PCMA
Required parameters: rate
The RTP timestamp clock rate, which is equal to the sampling
rate. The typical rate is 8000, but other rates may be
specified.
Optional parameters: channels, ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: PCMU
Required parameters: rate
The RTP timestamp clock rate, which is equal to the sampling
rate. The typical rate is 8000, but other rates may be
specified.
Optional parameters: channels, ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: QCELP
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2658
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: RED
Required parameters:
pt: a comma-separated list of RTP payload types. Because
comma is a special character, the list must be a quoted-string
(enclosed in double quotes). For static payload types, each
list element is simply the type number. For dynamic payload
types, each list element is a mapping of the dynamic payload
type number to an embedded MIME content-type specification for
the payload format corresponding to the dynamic payload type.
The format of the mapping is:
dynamic-payload-type "=" content-type
If the content-type string includes a comma, then the content-type string MUST be a quoted-string. If the content- type string does not include a comma, it MAY still be quoted. Since it is part of the list which must itself be a quoted- string, that means the quotation marks MUST be quoted with backslash quoting as specified in RFC 2045. If the content- type string itself contains a quoted-string, then the requirement for backslash quoting is recursively applied. To specify the audio/RED payload format in SDP, the pt parameter is mapped to an a=fmtp attribute by eliminating the parameter name (pt) and changing the commas to slashes. For example, 'pt="0,5"' maps to 'a=fmtp:99 0/5'. A more complicated example, with a dynamic payload type, is:
pt = "0, 103 = \"audio/G729D;annexb=yes\" "
m=audio 49170 RTP/AVP 99 0 103
a=rtpmap:99 RED/8000
a=fmtp:99 0/103
a=rtpmap:103 G729D/8000
a=fmtp:103 annexb=yes
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2198
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: audio
MIME subtype name: VDVI
Required parameters: None
Optional parameters: ptime, maxptime
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
For all of the video payload formats registered here, the RTP timestamp clock rate is always 90000 Hz, so the "rate" parameter is not applicable. Likewise, the "channel" parameter is not used with video, and while "ptime" and "maxptime" could be used with video, they typically are not.
MIME media type name: video
MIME subtype name: BT656
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2431
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: CelB
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2029
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: JPEG
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2435
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: H261
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2032
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: H263
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2190
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: H263-1998
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2429
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: H263-2000
Required parameters: None
Optional parameters:
profile: H.263 profile number, in the range 0 through 10,
specifying the supported H.263 annexes/subparts.
level: Level of bitstream operation, in the range 0 through 100, specifying the level of computational complexity of the decoding process.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2429
The specific values for the profile and level parameters and
their meaning are defined in Annex X of ITU-T Recommendation
H.263, "Video coding for low bit rate communication". Note
that the RTP payload format for H263-2000 is the same as for
H263-1998, but additional annexes/subparts are specified along
with the profiles and levels.
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: MPV
MPEG-1 or -2 Elementary Streams
Required parameters: None
Optional parameters:
type: the type of MPEG video, from the set "mpeg1",
"mpeg2-halfd1", or "mpeg2-fulld1". The default is "mpeg1".
The mapping to a=fmtp is identity.
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2250
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: MP2T
MPEG-2 Transport Streams
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2250
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: MP1S
MPEG-1 Systems Streams
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2250
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: MP2P
MPEG-2 Program Streams
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2250
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: BMPEG
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 2343
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
MIME media type name: video
MIME subtype name: nv
Required parameters: None
Optional parameters: None
Encoding considerations:
This type is only defined for transfer via RTP [RFC 3550].
Security considerations: See Section 5 of RFC 3555
Interoperability considerations: none
Published specification: RFC 3551
Applications which use this media type:
Audio and video streaming and conferencing tools.
Additional information: none
Person & email address to contact for further information: Stephen Casner <casner@acm.org>
Intended usage: COMMON
Author/Change controller:
Stephen Casner
The MIME subtype registration procedure specified in this memo does not impose any security considerations on its own. This memo also contains several MIME type registrations. The registrations themselves do not impose security risks, but some may state security considerations specific to the particular registration.
Several audio and video encodings are perfect for hiding data using steganography.
The RTP specification, RFC 3550, provides security considerations for the transport of audio and video data over RTP, including the use of encryption where confidentiality is required.
[1] Freed, N., Klensin, J. and J. Postel, "Multipurpose Internet Mail Extensions (MIME) Part Four: Registration Procedures", BCP 13, RFC 2048, November 1996.
[2] Schulzrinne, H., Casner, S., Frederick, R. and V. Jacobson, "RTP: A Transport Protocol for Real-Time Applications", RFC 3550, July 2003.
[3] Schulzrinne, H. and S. Casner, "RTP Profile for Audio and Video Conferences with Minimal Control", RFC 3551, July 2003.
[4] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997.
[5] Handley, M. and V. Jacobson, "SDP: Session Description Protocol", RFC 2327, April 1998.
[6] Freed, N. and N. Borenstein, "Multipurpose Internet Mail Extensions (MIME) Part One: Format of Internet Message Bodies", RFC 2045, November 1996.
[7] Kobayashi, K., Ogawa, A., Casner, S. and C. Bormann, "RTP Payload Format for 12-bit DAT Audio and 20- and 24-bit Linear Sampled Audio", RFC 3190, January 2002.
Stephen L. Casner
Packet Design
3400 Hillview Avenue, Building 3
Palo Alto, CA 94304
United States
Phone: +1 650 739-1843
EMail: casner@acm.org
Philipp Hoschka
INRIA
Route des Lucioles 2004
06904, Sophia-Antipolis Cedex
BP 93, France
Phone: (+33) 4 92 38 79 84
Fax: (+33) 4 92 38 77 65 EMail: ph@w3.org
W3C
http://www.w3.org/people/hoschka
Copyright © The Internet Society (2003). All Rights Reserved.
This document and translations of it may be copied and furnished to others, and derivative works that comment on or otherwise explain it or assist in its implementation may be prepared, copied, published and distributed, in whole or in part, without restriction of any kind, provided that the above copyright notice and this paragraph are included on all such copies and derivative works. However, this document itself may not be modified in any way, such as by removing the copyright notice or references to the Internet Society or other Internet organizations, except as needed for the purpose of developing Internet standards in which case the procedures for copyrights defined in the Internet Standards process must be followed, or as required to translate it into languages other than English.
The limited permissions granted above are perpetual and will not be revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Funding for the RFC Editor function is currently provided by the Internet Society.