|
Network Working Group Request for Comments: 1970 Category: Standards Track |
T. Narten IBM E. Nordmark Sun Microsystems W. Simpson Daydreamer August 1996 |
This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited.
This document specifies the Neighbor Discovery protocol for IP Version 6. IPv6 nodes on the same link use Neighbor Discovery to discover each other's presence, to determine each other's link-layer addresses, to find routers and to maintain reachability information about the paths to active neighbors.
1. INTRODUCTION
2. TERMINOLOGY
2.1. General
2.2. Link Types
2.3. Addresses
2.4. Requirements
3. PROTOCOL OVERVIEW
3.1. Comparison with IPv4
3.2. Supported Link Types
4. MESSAGE FORMATS
4.1. Router Solicitation Message Format
4.2. Router Advertisement Message Format
4.3. Neighbor Solicitation Message Format
4.4. Neighbor Advertisement Message Format
4.5. Redirect Message Format
4.6. Option Formats
4.6.1. Source/Target Link-layer Address
4.6.2. Prefix Information
4.6.3. Redirected Header
4.6.4. MTU
5. CONCEPTUAL MODEL OF A HOST
5.1. Conceptual Data Structures
5.2. Conceptual Sending Algorithm
5.3. Garbage Collection and Timeout Requirements
6. ROUTER AND PREFIX DISCOVERY
6.1. Message Validation
6.1.1. Validation of Router Solicitation Messages
6.1.2. Validation of Router Advertisement Messages
6.2. Router Specification
6.2.1. Router Configuration Variables
6.2.2. Becoming An Advertising Interface
6.2.3. Router Advertisement Message Content
6.2.4. Sending Unsolicited Router Advertisements
6.2.5. Ceasing To Be An Advertising Interface
6.2.6. Processing Router Solicitations
6.2.7. Router Advertisement Consistency
6.2.8. Link-local Address Change
6.3. Host Specification
6.3.1. Host Configuration Variables
6.3.2. Host Variables
6.3.3. Interface Initialization
6.3.4. Processing Received Router Advertisements
6.3.5. Timing out Prefixes and Default Routers
6.3.6. Default Router Selection
6.3.7. Sending Router Solicitations
7. ADDRESS RESOLUTION AND NEIGHBOR UNREACHABILITY DETECTION. 55
7.1. Message Validation
7.1.1. Validation of Neighbor Solicitations
7.1.2. Validation of Neighbor Advertisements
7.2. Address Resolution
7.2.1. Interface Initialization
7.2.2. Sending Neighbor Solicitations
7.2.3. Receipt of Neighbor Solicitations
7.2.4. Sending Solicited Neighbor Advertisements
7.2.5. Receipt of Neighbor Advertisements
7.2.6. Sending Unsolicited Neighbor Advertisements
7.2.7. Anycast Neighbor Advertisements
7.2.8. Proxy Neighbor Advertisements
7.3. Neighbor Unreachability Detection
7.3.1. Reachability Confirmation
7.3.2. Neighbor Cache Entry States
7.3.3. Node Behavior
8. REDIRECT FUNCTION
8.1. Validation of Redirect Messages
8.2. Router Specification
8.3. Host Specification
9. EXTENSIBILITY - OPTION PROCESSING
10. PROTOCOL CONSTANTS
11. SECURITY CONSIDERATIONS
REFERENCES
AUTHORS' ADDRESSES
APPENDIX A: MULTIHOMED HOSTS
APPENDIX B: FUTURE EXTENSIONS
APPENDIX C: STATE MACHINE FOR THE REACHABILITY STATE
APPENDIX D: IMPLEMENTATION ISSUES
Appendix D.1: Reachability confirmations
This specification defines the Neighbor Discovery (ND) protocol for Internet Protocol Version 6 (IPv6). Nodes (hosts and routers) use Neighbor Discovery to determine the link-layer addresses for neighbors known to reside on attached links and to quickly purge cached values that become invalid. Hosts also use Neighbor Discovery to find neighboring routers that are willing to forward packets on their behalf. Finally, nodes use the protocol to actively keep track of which neighbors are reachable and which are not, and to detect changed link-layer addresses. When a router or the path to a router fails, a host actively searches for functioning alternates.
Unless specified otherwise (in a document that covers operating IP over a particular link type) this document applies to all link types. However, because ND uses link-layer multicast for some of its services, it is possible that on some link types (e.g., NBMA links) alternative protocols or mechanisms to implement those services will be specified (in the appropriate document covering the operation of IP over a particular link type). The services described in this document that are not directly dependent on multicast, such as Redirects, Next-hop determination, Neighbor Unreachability Detection, etc., are expected to be provided as specified in this document. The details of how one uses ND on NBMA links is an area for further study.
The authors would like to acknowledge the contributions the IPNGWG working group and, in particular, (in alphabetical order) Ran Atkinson, Jim Bound, Scott Bradner, Alex Conta, Stephen Deering, Francis Dupont, Robert Elz, Robert Gilligan, Robert Hinden, Allison Mankin, Dan McDonald, Charles Perkins, Matt Thomas, and Susan Thomson.
IP - Internet Protocol Version 6. The terms IPv4 and IPv6
are used only in contexts where necessary to avoid
ambiguity.
ICMP - Internet Message Control Protocol for the Internet
Protocol Version 6. The terms ICMPv4 and ICMPv6 are
used only in contexts where necessary to avoid
ambiguity.
node - a device that implements IP.
router - a node that forwards IP packets not explicitly
addressed to itself.
host - any node that is not a router.
upper layer - a protocol layer immediately above IP. Examples are transport protocols such as TCP and UDP, control protocols such as ICMP, routing protocols such as OSPF, and internet or lower-layer protocols being "tunneled" over (i.e., encapsulated in) IP such as IPX, AppleTalk, or IP itself.
link - a communication facility or medium over which nodes can
communicate at the link layer, i.e., the layer
immediately below IP. Examples are Ethernets (simple
or bridged), PPP links, X.25, Frame Relay, or ATM
networks as well as internet (or higher) layer
"tunnels", such as tunnels over IPv4 or IPv6 itself.
interface - a node's attachment to a link.
neighbors - nodes attached to the same link.
address - an IP-layer identifier for an interface or a set of
interfaces.
anycast address
- an identifier for a set of interfaces (typically
belonging to different nodes). A packet sent to an
anycast address is delivered to one of the interfaces
identified by that address (the "nearest" one,
according to the routing protocol's measure of
distance). See [ADDR-ARCH].
Note that an anycast address is syntactically indistinguishable from a unicast address. Thus, nodes sending packets to anycast addresses don't generally know that an anycast address is being used. Throughout the rest of this document, references to unicast addresses also apply to anycast addresses in those cases where the node is unaware that a unicast address is actually an anycast address.
prefix - a bit string that consists of some number of initial
bits of an address.
link-layer address
- a link-layer identifier for an interface. Examples
include IEEE 802 addresses for Ethernet links and E.164
addresses for ISDN links.
on-link - an address that is assigned to an interface on a
specified link. A node considers an address to be on-
link if:
- it is covered by one of the link's prefixes, or
- a neighboring router specifies the address as the
target of a Redirect message, or
- a Neighbor Advertisement message is received for
the (target) address, or
- any Neighbor Discovery message is received from the
address.
off-link - the opposite of "on-link"; an address that is not
assigned to any interfaces on the specified link.
longest prefix match
- The process of determining which prefix (if any) in a
set of prefixes covers a target address. A target
address is covered by a prefix if all of the bits in
the prefix match the left-most bits of the target
address. When multiple prefixes cover an address, the
longest prefix is the one that matches.
reachability
- whether or not the one-way "forward" path to a neighbor
is functioning properly. In particular, whether
packets sent to a neighbor are reaching the IP layer on
the neighboring machine and are being processed
properly by the receiving IP layer. For neighboring routers, reachability means that packets sent by a node's IP layer are delivered to the router's IP layer, and the router is indeed forwarding packets (i.e., it is configured as a router, not a host). For hosts, reachability means that packets sent by a node's IP layer are delivered to the neighbor host's IP layer.
packet - an IP header plus payload.
link MTU - the maximum transmission unit, i.e., maximum packet
size in octets, that can be conveyed in one piece over
a link.
target - an address about which address resolution information
is sought, or an address which is the new first-hop
when being redirected.
proxy - a router that responds to Neighbor Discovery query
messages on behalf of another node. A router acting on
behalf of a mobile node that has moved off-link could
potentially act as a proxy for the mobile node.
ICMP destination unreachable indication
- an error indication returned to the original sender of
a packet that cannot be delivered for the reasons
outlined in [ICMPv6]. If the error occurs on a node
other than the node originating the packet, an ICMP
error message is generated. If the error occurs on the
originating node, an implementation is not required to
actually create and send an ICMP error packet to the
source, as long as the upper-layer sender is notified
through an appropriate mechanism (e.g., return value
from a procedure call). Note, however, that an
implementation may find it convenient in some cases to
return errors to the sender by taking the offending
packet, generating an ICMP error message, and then
delivering it (locally) through the generic error
handling routines.
random delay
- when sending out messages, it is sometimes necessary to
delay a transmission for a random amount of time in
order to prevent multiple nodes from transmitting at
exactly the same time, or to prevent long-range
periodic transmissions from synchronizing with each
other [SYNC]. When a random component is required, a
node calculates the actual delay in such a way that the
computed delay forms a uniformly-distributed random value that falls between the specified minimum and maximum delay times. The implementor must take care to insure that the granularity of the calculated random component and the resolution of the timer used are both high enough to insure that the probability of multiple nodes delaying the same amount of time is small.
random delay seed
- If a pseudo-random number generator is used in
calculating a random delay component, the generator
should be initialized with a unique seed prior to being
used. Note that it is not sufficient to use the
interface token alone as the seed, since interface
tokens will not always be unique. To reduce the
probability that duplicate interface tokens cause the
same seed to be used, the seed should be calculated
from a variety of input sources (e.g., machine
components) that are likely to be different even on
identical "boxes". For example, the seed could be
formed by combining the CPU's serial number with an
interface token.
Different link layers have different properties. The ones of concern to Neighbor Discovery are:
multicast - a link that supports a native mechanism at the link
layer for sending packets to all (i.e., broadcast)
or a subset of all neighbors.
point-to-point - a link that connects exactly two interfaces. A point-to-point link is assumed to have multicast capability and have a link-local address.
non-broadcast multi-access (NBMA)
- a link to which more than two interfaces can attach,
but that does not support a native form of multicast
or broadcast (e.g., X.25, ATM, frame relay, etc.).
Note that all link types (including NBMA) are
expected to provide multicast service for IP (e.g.,
using multicast servers), but it is an issue for
further study whether ND should use such facilities
or an alternate mechanism that provides the
equivalent ND services.
shared media - a link that allows direct communication among a
number of nodes, but attached nodes are configured in such a way that they do not have complete prefix information for all on-link destinations. That is, at the IP level, nodes on the same link may not know that they are neighbors; by default, they communicate through a router. Examples are large (switched) public data networks such as SMDS and B- ISDN. Also known as "large clouds". See [SH- MEDIA].
variable MTU - a link that does not have a well-defined MTU (e.g.,
IEEE 802.5 token rings). Many links (e.g.,
Ethernet) have a standard MTU defined by the link-
layer protocol or by the specific document
describing how to run IP over the link layer.
asymmetric reachability
- a link where non-reflexive and/or non-transitive
reachability is part of normal operation. (Non-
reflexive reachability means packets from A reach B
but packets from B don't reach A. Non-transitive
reachability means packets from A reach B, and
packets from B reach C, but packets from A don't
reach C.) Many radio links exhibit these
properties.
Neighbor Discovery makes use of a number of different addresses defined in [ADDR-ARCH], including:
all-nodes multicast address
- the link-local scope address to reach all nodes.
FF02::1
all-routers multicast address
- the link-local scope address to reach all routers.
FF02::2
solicited-node multicast address
- a link-local scope multicast address that is computed
as a function of the solicited target's address. The
solicited-node multicast address is formed by taking
the low-order 32 bits of the target IP address and
appending those bits to the 96-bit prefix
FF02:0:0:0:0:1 to produce a multicast address within
the range FF02::1:0:0 to FF02::1:FFFF:FFFF. For
example, the solicited node multicast address
corresponding to the IP address 4037::01:800:200E:8C6C is FF02::1:200E:8C6C. IP addresses that differ only in the high-order bits, e.g., due to multiple high-order prefixes associated with different providers, will map to the same solicited-node address thereby reducing the number of multicast addresses a node must join.
link-local address
- a unicast address having link-only scope that can be
used to reach neighbors. All interfaces on routers
MUST have a link-local address. Also, [ADDRCONF]
requires that interfaces on hosts have a link-local
address.
unspecified address
- a reserved address value that indicates the lack of an
address (e.g., the address is unknown). It is never
used as a destination address, but may be used as a
source address if the sender does not (yet) know its
own address (e.g., while verifying an address is unused
during address autoconfiguration [ADDRCONF]). The
unspecified address has a value of 0:0:0:0:0:0:0:0.
Throughout this document, the words that are used to define the significance of the particular requirements are capitalized. These words are:
MUST
This word or the adjective "REQUIRED" means that the item is an
absolute requirement of this specification.
MUST NOT
This phrase means the item is an absolute prohibition of this
specification.
SHOULD
This word or the adjective "RECOMMENDED" means that there may
exist valid reasons in particular circumstances to ignore this
item, but the full implications should be understood and the
case carefully weighed before choosing a different course.
SHOULD NOT
This phrase means that there may exist valid reasons in
particular circumstances when the listed behavior is acceptable
or even useful, but the full implications should be understood
and the case carefully weighted before implementing any behavior
described with this label.
MAY This word or the adjective "OPTIONAL" means that this item is truly optional. One vendor may choose to include the item because a particular marketplace requires it or because it enhances the product, for example, another vendor may omit the same item.
This document also makes use of internal conceptual variables to describe protocol behavior and external variables that an implementation must allow system administrators to change. The specific variable names, how their values change, and how their settings influence protocol behavior are provided to demonstrate protocol behavior. An implementation is not required to have them in the exact form described here, so long as its external behavior is consistent with that described in this document.
This protocol solves a set of problems related to the interaction between nodes attached to the same link. It defines mechanisms for solving each of the following problems:
Router Discovery: How hosts locate routers that reside on an attached link.
Prefix Discovery: How hosts discover the set of address prefixes that define which destinations are on-link for an attached link. (Nodes use prefixes to distinguish destinations that reside on-link from those only reachable through a router.)
Parameter Discovery: How a node learns such link parameters as the link MTU or such Internet parameters as the hop limit value to place in outgoing packets.
Address Autoconfiguration: How nodes automatically configure an address for an interface.
Address resolution: How nodes determine the link-layer address of an on-link destination (e.g., a neighbor) given only the destination's IP address.
Next-hop determination: The algorithm for mapping an IP destination address into the IP address of the neighbor to which traffic for the destination should be sent. The next-hop can be a router or the destination itself.
Neighbor Unreachability Detection: How nodes determine that a neighbor is no longer reachable. For neighbors used as routers, alternate default routers can be tried. For both routers and hosts, address resolution can be performed again.
Duplicate Address Detection: How a node determines that an address it wishes to use is not already in use by another node.
Redirect: How a router informs a host of a better first-hop node to reach a particular destination.
Neighbor Discovery defines five different ICMP packet types: A pair of Router Solicitation and Router Advertisement messages, a pair of Neighbor Solicitation and Neighbor Advertisements messages, and a Redirect message. The messages serve the following purpose:
Router Solicitation: When an interface becomes enabled, hosts may send out Router Solicitations that request routers to generate Router Advertisements immediately rather than at their next scheduled time.
Router Advertisement: Routers advertise their presence together with various link and Internet parameters either periodically, or in response to a Router Solicitation message. Router Advertisements contain prefixes that are used for on-link determination and/or address configuration, a suggested hop limit value, etc.
Neighbor Solicitation: Sent by a node to determine the link-layer address of a neighbor, or to verify that a neighbor is still reachable via a cached link-layer address. Neighbor Solicitations are also used for Duplicate Address Detection.
Neighbor Advertisement: A response to a Neighbor Solicitation message. A node may also send unsolicited Neighbor Advertisements to announce a link-layer address change.
Redirect: Used by routers to inform hosts of a better first hop for a destination.
On multicast-capable links, each router periodically multicasts a Router Advertisement packet announcing its availability. A host receives Router Advertisements from all routers, building a list of default routers. Routers generate Router Advertisements frequently enough that hosts will learn of their presence within a few minutes, but not frequently enough to rely on an absence of advertisements to
detect router failure; a separate Neighbor Unreachability Detection algorithm provides failure detection.
Router Advertisements contain a list of prefixes used for on-link determination and/or autonomous address configuration; flags associated with the prefixes specify the intended uses of a particular prefix. Hosts use the advertised on-link prefixes to build and maintain a list that is used in deciding when a packet's destination is on-link or beyond a router. Note that a destination can be on-link even though it is not covered by any advertised on- link prefix. In such cases a router can send a Redirect informing the sender that the destination is a neighbor.
Router Advertisements (and per-prefix flags) allow routers to inform hosts how to perform Address Autoconfiguration. For example, routers can specify whether hosts should use stateful (DHCPv6) and/or autonomous (stateless) address configuration. The exact semantics and usage of the address configuration-related information is specified in [ADDRCONF].
Router Advertisement messages also contain Internet parameters such as the hop limit that hosts should use in outgoing packets and, optionally, link parameters such as the link MTU. This facilitates centralized administration of critical parameters that can be set on routers and automatically propagated to all attached hosts.
Nodes accomplish address resolution by multicasting a Neighbor Solicitation that asks the target node to return its link-layer address. Neighbor Solicitation messages are multicast to the solicited-node multicast address of the target address. The target returns its link-layer address in a unicast Neighbor Advertisement message. A single request-response pair of packets is sufficient for both the initiator and the target to resolve each other's link-layer addresses; the initiator includes its link-layer address in the Neighbor Solicitation.
Neighbor Solicitation messages can also be used to determine if more than one node has been assigned the same unicast address. The use of Neighbor Solicitation messages for Duplicate Address Detection is specified in [ADDRCONF].
Neighbor Unreachability Detection detects the failure of a neighbor or the failure of the forward path to the neighbor. Doing so requires positive confirmation that packets sent to a neighbor are actually reaching that neighbor and being processed properly by its IP layer. Neighbor Unreachability Detection uses confirmation from two sources. When possible, upper-layer protocols provide a positive confirmation that a connection is making "forward progress", that is,
previously sent data is known to have been delivered correctly (e.g., new acknowledgments were received recently). When positive confirmation is not forthcoming through such "hints", a node sends unicast Neighbor Solicitation messages that solicit Neighbor Advertisements as reachability confirmation from the next hop. To reduce unnecessary network traffic, probe messages are only sent to neighbors to which the node is actively sending packets.
In addition to addressing the above general problems, Neighbor Discovery also handles the following situations:
Link-layer address change - A node that knows its link-layer address has changed can multicast a few (unsolicited) Neighbor Advertisement packets to all nodes to quickly update cached link-layer addresses that have become invalid. Note that the sending of unsolicited advertisements is a performance enhancement only (e.g., unreliable). The Neighbor Unreachability Detection algorithm ensures that all nodes will reliably discover the new address, though the delay may be somewhat longer.
Inbound load balancing - Nodes with replicated interfaces may want to load balance the reception of incoming packets across multiple network interfaces on the same link. Such nodes have multiple link-layer addresses assigned to the same interface. For example, a single network driver could represent multiple network interface cards as a single logical interface having multiple link-layer addresses. Load balancing is handled by allowing routers to omit the source link-layer address from Router Advertisement packets, thereby forcing neighbors to use Neighbor Solicitation messages to learn link-layer addresses of routers. Returned Neighbor Advertisement messages can then contain link-layer addresses that differ depending on who issued the solicitation.
Anycast addresses - Anycast addresses identify one of a set of nodes providing an equivalent service, and multiple nodes on the same link may be configured to recognize the same Anycast address. Neighbor Discovery handles anycasts by having nodes expect to receive multiple Neighbor Advertisements for the same target. All advertisements for anycast addresses are tagged as being non-Override advertisements. This invokes specific rules to determine which of potentially multiple advertisements should be used.
Proxy advertisements - A router willing to accept packets on behalf of a target address that is unable to respond to Neighbor Solicitations can issue non-Override Neighbor Advertisements.
There is currently no specified use of proxy, but proxy advertising could potentially be used to handle cases like mobile nodes that have moved off-link. However, it is not intended as a general mechanism to handle nodes that, e.g., do not implement this protocol.
The IPv6 Neighbor Discovery protocol corresponds to a combination of the IPv4 protocols ARP [ARP], ICMP Router Discovery [RDISC], and ICMP Redirect [ICMPv4]. In IPv4 there is no generally agreed upon protocol or mechanism for Neighbor Unreachability Detection, although Hosts Requirements [HR-CL] does specify some possible algorithms for Dead Gateway Detection (a subset of the problems Neighbor Unreachability Detection tackles).
The Neighbor Discovery protocol provides a multitude of improvements over the IPv4 set of protocols:
Router Discovery is part of the base protocol set; there is no need for hosts to "snoop" the routing protocols.
Router advertisements carry link-layer addresses; no additional packet exchange is needed to resolve the router's link-layer address.
Router advertisements carry prefixes for a link; there is no need to have a separate mechanism to configure the "netmask".
Router advertisements enable Address Autoconfiguration.
Routers can advertise an MTU for hosts to use on the link, ensuring that all nodes use the same MTU value on links lacking a well- defined MTU.
Address resolution multicasts are "spread" over 4 billion (2^32) multicast addresses greatly reducing address resolution related interrupts on nodes other than the target. Moreover, non-IPv6 machines should not be interrupted at all.
Redirects contain the link-layer address of the new first hop; separate address resolution is not needed upon receiving a redirect.
Multiple prefixes can be associated with the same link. By
default, hosts learn all on-link prefixes from Router
Advertisements. However, routers may be configured to omit some or
all prefixes from Router Advertisements. In such cases hosts
assume that destinations are off-link and send traffic to routers.
A router can then issue redirects as appropriate.
Unlike IPv4, the recipient of an IPv6 redirect assumes that the new next-hop is on-link. In IPv4, a host ignores redirects specifying a next-hop that is not on-link according to the link's network mask. The IPv6 redirect mechanism is analogous to the XRedirect facility specified in [SH-MEDIA]. It is expected to be useful on non-broadcast and shared media links in which it is undesirable or not possible for nodes to know all prefixes for on-link destinations.
Neighbor Unreachability Detection is part of the base significantly improving the robustness of packet delivery in the presence of failing routers, partially failing or partitioned links and nodes that change their link-layer addresses. For instance, mobile nodes can move off-link without losing any connectivity due to stale ARP caches.
Unlike ARP, Neighbor Discovery detects half-link failures (using Neighbor Unreachability Detection) and avoids sending traffic to neighbors with which two-way connectivity is absent.
Unlike in IPv4 Router Discovery the Router Advertisement messages do not contain a preference field. The preference field is not needed to handle routers of different "stability"; the Neighbor Unreachability Detection will detect dead routers and switch to a working one.
The use of link-local addresses to uniquely identify routers (for Router Advertisement and Redirect messages) makes it possible for hosts to maintain the router associations in the event of the site renumbering to use new global prefixes.
Using the Hop Limit equal to 255 trick Neighbor Discovery is immune to off-link senders that accidentally or intentionally send ND messages. In IPv4 off-link senders can send both ICMP Redirects and Router Advertisement messages.
Placing address resolution at the ICMP layer makes the protocol more media-independent than ARP and makes it possible to use standard IP authentication and security mechanisms as appropriate [IPv6-AUTH, IPv6-ESP].
Neighbor Discovery supports links with different properties. In the presence of certain properties only a subset of the ND protocol mechanisms are fully specified in this document:
point-to-point - Neighbor Discovery handles such links just like multicast links. (Multicast can be trivially provided on point to point links, and interfaces can be assigned link-local addresses.) Neighbor Discovery should be implemented as described in this document.
multicast - Neighbor Discovery should be implemented as
described in this document.
non-broadcast multiple access (NBMA)
- Redirect, Neighbor Unreachability Detection and
next-hop determination should be implemented as
described in this document. Address resolution, and
the mechanism for delivering Router Solicitations
and Advertisements on NBMA links is not specified in
this document. Note that if hosts support manual
configuration of a list of default routers, hosts
can dynamically acquire the link-layer addresses for
their neighbors from Redirect messages.
shared media - The Redirect message is modeled after the XRedirect
message in [SH-MEDIA] in order to simplify use of
the protocol on shared media links.
This specification does not address shared media issues that only relate to routers, such as:
- How routers exchange reachability information on
a shared media link.
- How a router determines the link-layer address of
a host, which it needs to send redirect messages
to the host.
- How a router determines that it is the first-hop
router for a received packet.
The protocol is extensible (through the definition of new options) so that other solutions might be possible in the future.
variable MTU - Neighbor Discovery allows routers to specify a MTU
for the link, which all nodes then use. All nodes
on a link must use the same MTU (or Maximum Receive
Unit) in order for multicast to work properly.
Otherwise when multicasting a sender, which can not
know which nodes will receive the packet, could not
determine a minimum packet size all receivers can
process.
asymmetric reachability
- Neighbor Discovery detects the absence of symmetric
reachability; a node avoids paths to a neighbor with
which it does not have symmetric connectivity.
The Neighbor Unreachability Detection will typically identify such half-links and the node will refrain from using them.
The protocol can presumably be extended in the future to find viable paths in environments that lack reflexive and transitive connectivity.
Hosts send Router Solicitations in order to prompt routers to generate Router Advertisements quickly.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Source Address
An IP address assigned to the sending interface, or
the unspecified address if no address is assigned to
the sending interface.
Destination Address
Typically the all-routers multicast address.
Hop Limit 255 Priority 15
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the destination
address, then the sender SHOULD include this header.
Type 133
Code 0
Checksum The ICMP checksum. See [ICMPv6].
Reserved This field is unused. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Source link-layer address
The link-layer address of the sender, if known.
Future versions of this protocol may define new option types. Receivers MUST silently ignore any options they do not recognize and continue processing the message.
Routers send out Router Advertisement message periodically, or in response to a Router Solicitation.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Cur Hop Limit |M|O| Reserved | Router Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reachable Time |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Retrans Timer |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Source Address
MUST be the link-local address assigned to the
interface from which this message is sent.
Destination Address
Typically the Source Address of an invoking Router
Solicitation or the all-nodes multicast address.
Hop Limit 255 Priority 15
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the destination
address, then the sender SHOULD include this header.
Type 134 Code 0 Checksum The ICMP checksum. See [ICMPv6].
Cur Hop Limit 8-bit unsigned integer. The default value that should be placed in the Hop Count field of the IP header for outgoing IP packets. A value of zero means unspecified (by this router).
M 1-bit "Managed address configuration" flag. When set,
hosts use the administered (stateful) protocol for
address autoconfiguration in addition to any addresses
autoconfigured using stateless address
autoconfiguration. The use of this flag is described
in [ADDRCONF].
O 1-bit "Other stateful configuration" flag. When set,
hosts use the administered (stateful) protocol for
autoconfiguration of other (non-address) information.
The use of this flag is described in [ADDRCONF].
Reserved A 6-bit unused field. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Router Lifetime
16-bit unsigned integer. The lifetime associated with
the default router in units of seconds. The maximum
value corresponds to 18.2 hours. A Lifetime of 0
indicates that the router is not a default router and
SHOULD NOT appear on the default router list. The
Router Lifetime applies only to the router's
usefulness as a default router; it does not apply to
information contained in other message fields or
options. Options that need time limits for their
information include their own lifetime fields.
Reachable Time 32-bit unsigned integer. The time, in milliseconds, that a node assumes a neighbor is reachable after having received a reachability confirmation. Used by the Neighbor Unreachability Detection algorithm (see Section 7.3). A value of zero means unspecified (by this router).
Retrans Timer 32-bit unsigned integer. The time, in milliseconds, between retransmitted Neighbor Solicitation messages. Used by address resolution and the Neighbor Unreachability Detection algorithm (see Sections 7.2 and 7.3). A value of zero means unspecified (by this router).
Source link-layer address
The link-layer address of the interface from which the
Router Advertisement is sent. Only used on link
layers that have addresses. A router MAY omit this
option in order to enable inbound load sharing across
multiple link-layer addresses.
MTU SHOULD be sent on links that have a variable MTU (as
specified in the document that describes how to run IP
over the particular link type). MAY be sent on other
links.
Prefix Information
These options specify the prefixes that are on-link
and/or are used for address autoconfiguration. A
router SHOULD include all its on-link prefixes (except
the link-local prefix) so that multihomed hosts have
complete prefix information about on-link destinations
for the links to which they attach. If complete
information is lacking, a multihomed host may not be
able to chose the correct outgoing interface when sending traffic to its neighbors.
Future versions of this protocol may define new option types. Receivers MUST silently ignore any options they do not recognize and continue processing the message.
Nodes send Neighbor Solicitations to request the link-layer address of a target node while also providing their own link-layer address to the target. Neighbor Solicitations are multicast when the node needs to resolve an address and unicast when the node seeks to verify the reachability of a neighbor.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Target Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Source Address
Either an address assigned to the interface from which
this message is sent or (if Duplicate Address
Detection is in progress [ADDRCONF]) the unspecified
address.
Destination Address
Either the solicited-node multicast address
corresponding to the target address, or the target
address.
Hop Limit 255
Priority 15
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the destination
address, then the sender SHOULD include this header.
Type 135
Code 0
Checksum The ICMP checksum. See [ICMPv6].
Reserved This field is unused. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Target Address
The IP address of the target of the solicitation. It
MUST NOT be a multicast address.
Source link-layer address
The link-layer address for the sender. On link layers
that have addresses this option MUST be included in
multicast solicitations and SHOULD be included in
unicast solicitations.
Future versions of this protocol may define new option types. Receivers MUST silently ignore any options they do not recognize and continue processing the message.
A node sends Neighbor Advertisements in response to Neighbor Solicitations and sends unsolicited Neighbor Advertisements in order to (unreliably) propagate new information quickly.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|R|S|O| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Target Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Source Address
An address assigned to the interface from which the
advertisement is sent.
Destination Address
For solicited advertisements, the Source Address of an
invoking Neighbor Solicitation or, if the
solicitation's Source Address is the unspecified
address, the all-nodes multicast address.
For unsolicited advertisements typically the all-nodes multicast address.
Hop Limit 255 Priority 15
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the destination
address, then the sender SHOULD include this header.
Type 136
Code 0
Checksum The ICMP checksum. See [ICMPv6].
R Router flag. When set, the R-bit indicates that the
sender is a router. The R-bit is used by Neighbor
Unreachability Detection to detect a router that
changes to a host.
S Solicited flag. When set, the S-bit indicates that
the advertisement was sent in response to a Neighbor
Solicitation from the Destination address. The S-bit
is used as a reachability confirmation for Neighbor
Unreachability Detection. It MUST NOT be set in
multicast advertisements or in unsolicited unicast
advertisements.
O Override flag. When set, the O-bit indicates that the
advertisement should override an existing cache entry
and update the cached link-layer address. When it is
not set the advertisement will not update a cached
link-layer address though it will update an existing
Neighbor Cache entry for which no link-layer address
is known. It SHOULD NOT be set in solicited
advertisements for anycast addresses and in solicited
proxy advertisements. It SHOULD be set in other
solicited advertisements and in unsolicited
advertisements.
Reserved 29-bit unused field. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Target Address
For solicited advertisements, the Target Address field
in the Neighbor Solicitation message that prompted
this advertisement. For an unsolicited advertisement,
the address whose link-layer address has changed. The
Target Address MUST NOT be a multicast address.
Target link-layer address
The link-layer address for the target, i.e., the
sender of the advertisement. MUST be included on link
layers that have addresses.
Future versions of this protocol may define new option types. Receivers MUST silently ignore any options they do not recognize and continue processing the message.
Routers send Redirect packets to inform a host of a better first-hop node on the path to a destination. Hosts can be redirected to a better first-hop router but can also be informed by a redirect that the destination is in fact a neighbor. The latter is accomplished by setting the ICMP Target Address equal to the ICMP Destination Address.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Code | Checksum |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Target Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Destination Address +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Options ...
+-+-+-+-+-+-+-+-+-+-+-+-
Source Address
MUST be the link-local address assigned to the
interface from which this message is sent.
Destination Address
The Source Address of the packet that triggered the
redirect.
Hop Limit 255 Priority 15
Authentication Header
If a Security Association for the IP Authentication
Header exists between the sender and the destination
address, then the sender SHOULD include this header.
Type 137
Code 0
Checksum The ICMP checksum. See [ICMPv6].
Reserved This field is unused. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Target Address An IP address that is a better first hop to use for the ICMP Destination Address. When the target is the actual endpoint of communication, i.e., the destination is a neighbor, the Target Address field MUST contain the same value as the ICMP Destination Address field. Otherwise the target is a better first-hop router and the Target Address MUST be the router's link-local address so that hosts can uniquely identify routers.
Destination Address
The IP address of the destination which is redirected
to the target.
Target link-layer address
The link-layer address for the target. It SHOULD be
included (if known). Note that on NBMA links, hosts
may rely on the presence of the Target Link-Layer
Address option in Redirect messages as the means for
determining the link-layer addresses of neighbors. In
such cases, the option MUST be included in Redirect
messages.
Redirected Header
As much as possible of the IP packet that triggered
the sending of the Redirect without making the
redirect packet exceed 576 octets.
Neighbor Discovery messages include zero or more options, some of which may appear multiple times in the same message. All options are of the form:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 8-bit identifier of the type of option. The options
defined in this document are:
Option Name Type
Source Link-Layer Address 1
Target Link-Layer Address 2
Prefix Information 3
Redirected Header 4
MTU 5
Length 8-bit unsigned integer. The length of the option in
units of 8 octets. The value 0 is invalid. Nodes
MUST silently discard an ND packet that contains an
option with length zero.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Link-Layer Address ...
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type
1 for Source Link-layer Address
2 for Target Link-layer Address
Length The length of the option in units of 8 octets. For
example, the length for IEEE 802 addresses is 1
[IPv6-ETHER].
Link-Layer Address
The variable length link-layer address.
The content and format of this field (including byte and bit ordering) is expected to be specified in specific documents that describe how IPv6 operates over different link layers. For instance, [IPv6- ETHER].
The Target Link-Layer Address option contains the link-layer address of the target. It is used in Neighbor Advertisement and Redirect packets.
These options MUST be silently ignored for other Neighbor Discovery messages.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Prefix Length |L|A| Reserved1 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Valid Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Preferred Lifetime |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved2 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
| |
+ Prefix +
| |
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 3 Length 4
Prefix Length 8-bit unsigned integer. The number of leading bits in the Prefix that are valid. The value ranges from 0 to 128.
L 1-bit on-link flag. When set, indicates that this
prefix can be used for on-link determination. When
not set the advertisement makes no statement about
on-link or off-link properties of the prefix. For
instance, the prefix might be used for address
configuration with some of the addresses belonging to
the prefix being on-link and others being off-link.
A 1-bit autonomous address-configuration flag. When set
indicates that this prefix can be used for autonomous
address configuration as specified in [ADDRCONF].
Reserved1 6-bit unused field. It MUST be initialized to zero by
the sender and MUST be ignored by the receiver.
Valid Lifetime
32-bit unsigned integer. The length of time in
seconds (relative to the time the packet is sent) that
the prefix is valid for the purpose of on-link
determination. A value of all one bits (0xffffffff)
represents infinity. The Valid Lifetime is also used
by [ADDRCONF].
Preferred Lifetime
32-bit unsigned integer. The length of time in
seconds (relative to the time the packet is sent) that
addresses generated from the prefix via stateless
address autoconfiguration remain preferred [ADDRCONF].
A value of all one bits (0xffffffff) represents
infinity. See [ADDRCONF].
Reserved2 This field is unused. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
Prefix An IP address or a prefix of an IP address. The
Prefix Length field contains the number of valid
leading bits in the prefix. The bits in the prefix
after the prefix length are reserved and MUST be
initialized to zero by the sender and ignored by the
receiver. A router SHOULD NOT send a prefix option
for the link-local prefix and a host SHOULD ignore
such a prefix option.
The Prefix Information option appears in Router Advertisement packets and MUST be silently ignored for other messages.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
~ IP header + data ~
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 4
Length The length of the option in units of 8 octets.
Reserved These fields are unused. They MUST be initialized to
zero by the sender and MUST be ignored by the
receiver.
IP header + data
The original packet truncated to ensure that the size
of the redirect message does not exceed 576 octets.
This option MUST be silently ignored for other Neighbor Discovery messages.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MTU |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type 5
Length 1
Reserved This field is unused. It MUST be initialized to zero
by the sender and MUST be ignored by the receiver.
MTU 32-bit unsigned integer. The recommended MTU for the
link.
This option MUST be silently ignored for other Neighbor Discovery messages.
In configurations in which heterogeneous technologies are bridged together, the maximum supported MTU may differ from one segment to another. If the bridges do not generate ICMP Packet Too Big messages, communicating nodes will be unable to use Path MTU to dynamically determine the appropriate MTU on a per- neighbor basis. In such cases, routers use the MTU option to specify an MTU value supported by all segments.
This section describes a conceptual model of one possible data structure organization that hosts (and to some extent routers) will maintain in interacting with neighboring nodes. The described organization is provided to facilitate the explanation of how the Neighbor Discovery protocol should behave. This document does not mandate that implementations adhere to this model as long as their external behavior is consistent with that described in this document.
This model is only concerned with the aspects of host behavior directly related to Neighbor Discovery. In particular, it does not concern itself with such issues as source address selection or the selecting of an outgoing interface on a multihomed host.
Hosts will need to maintain the following pieces of information for each interface:
Neighbor Cache
- A set of entries about individual neighbors to which
traffic has been sent recently. Entries are keyed on
the neighbor's on-link unicast IP address and contain
such information as its link-layer address, a flag
indicating whether the neighbor is a router or a host
(called IsRouter in this document), a pointer to any
queued packets waiting for address resolution to
complete, etc.
A Neighbor Cache entry also contains information used by the Neighbor Unreachability Detection algorithm, including the reachability state, the number of unanswered probes, and the time the next Neighbor Unreachability Detection event is scheduled to take place.
Destination Cache
- A set of entries about destinations to which traffic
has been sent recently. The Destination Cache
includes both on-link and off-link destinations and
provides a level of indirection into the Neighbor
Cache; the Destination Cache maps a destination IP
address to the IP address of the next-hop neighbor.
This cache is updated with information learned from
Redirect messages. Implementations may find it
convenient to store additional information not
directly related to Neighbor Discovery in Destination
Cache entries, such as the Path MTU (PMTU) and round
trip timers maintained by transport protocols.
Prefix List - A list of the prefixes that define a set of addresses that are on-link. Prefix List entries are created from information received in Router Advertisements. Each entry has an associated invalidation timer value (extracted from the advertisement) used to expire prefixes when they become invalid. A special "infinity" timer value specifies that a prefix remains valid forever, unless a new (finite) value is received in a subsequent advertisement.
The link-local prefix is considered to be on the prefix list with an infinite invalidation timer
regardless of whether routers are advertising a prefix for it. Received Router Advertisements SHOULD NOT modify the invalidation timer for the link-local prefix.
Default Router List
- A list of routers to which packets may be sent.
Router list entries point to entries in the Neighbor
Cache; the algorithm for selecting a default router
favors routers known to be reachable over those whose
reachability is suspect. Each entry also has an
associated invalidation timer value (extracted from
Router Advertisements) used to delete entries that are
no longer advertised.
Note that the above conceptual data structures can be implemented using a variety of techniques. One possible implementation is to use a single longest-match routing table for all of the above data structures. Regardless of the specific implementation, it is critical that the Neighbor Cache entry for a router is shared by all Destination Cache entries using that router in order to prevent redundant Neighbor Unreachability Detection probes.
Note also that other protocols (e.g. IPv6 Mobility) might add additional conceptual data structures. An implementation is at liberty to implement such data structures in any way it pleases. For example, an implementation could merge all conceptual data structures into a single routing table.
The Neighbor Cache contains information maintained by the Neighbor Unreachability Detection algorithm. A key piece of information is a neighbor's reachability state, which is one of five possible values.
The following definitions are informal; precise definitions can be found in Section 7.3.2.
INCOMPLETE Address resolution is in progress and the link-layer address of the neighbor has not yet been determined.
REACHABLE Roughly speaking, the neighbor is known to have been
reachable recently (within tens of seconds ago).
STALE The neighbor is no longer known to be reachable but until
traffic is sent to the neighbor, no attempt should be
made to verify its reachability.
DELAY The neighbor is no longer known to be reachable, and
traffic has recently be sent to the neighbor. Rather
than probe the neighbor immediately, however, delay sending probes for a short while in order to give upper layer protocols a chance to provide reachability confirmation.
PROBE The neighbor is no longer known to be reachable, and
unicast Neighbor Solicitation probes are being sent to
verify reachability.
When sending a packet to a destination, a node uses a combination of the Destination Cache, the Prefix List, and the Default Router List to determine the IP address of the appropriate next hop, an operation known as "next-hop determination". Once the IP address of the next hop is known, the Neighbor Cache is consulted for link-layer information about that neighbor.
Next-hop determination for a given unicast destination operates as follows. The sender performs a longest prefix match against the Prefix List to determine whether the packet's destination is on- or off-link. If the destination is on-link, the next-hop address is the same as the packet's destination address. Otherwise, the sender selects a router from the Default Router List (following the rules described in Section 6.3.6). If the Default Router List is empty, the sender assumes that the destination is on-link.
For efficiency reasons, next-hop determination is not performed on
every packet that is sent. Instead, the results of next-hop
determination computations are saved in the Destination Cache (which
also contains updates learned from Redirect messages). When the
sending node has a packet to send, it first examines the Destination
Cache. If no entry exists for the destination, next-hop
determination is invoked to create a Destination Cache entry.
Once the IP address of the next-hop node is known, the sender examines the Neighbor Cache for link-layer information about that neighbor. If no entry exists, the sender creates one, sets its state to INCOMPLETE, initiates Address Resolution, and then queues the data packet pending completion of address resolution. For multicast- capable interfaces Address Resolution consists of sending a Neighbor Solicitation message and waiting for a Neighbor Advertisement. When a Neighbor Advertisement response is received, the link-layer addresses is entered in the Neighbor Cache entry and the queued packet is transmitted. The address resolution mechanism is described in detail in Section 7.2.
For multicast packets the next-hop is always the (multicast) destination address and is considered to be on-link. The procedure for determining the link-layer address corresponding to a given IP multicast address can be found in a separate document that covers operating IP over a particular link type (e.g., [IPv6-ETHER]).
Each time a Neighbor Cache entry is accessed while transmitting a unicast packet, the sender checks Neighbor Unreachability Detection related information according to the Neighbor Unreachability Detection algorithm (Section 7.3). This unreachability check might result in the sender transmitting a unicast Neighbor Solicitation to verify that the neighbor is still reachable.
Next-hop determination is done the first time traffic is sent to a destination. As long as subsequent communication to that destination proceeds successfully, the Destination Cache entry continues to be used. If at some point communication ceases to proceed, as determined by the Neighbor Unreachability Detection algorithm, next- hop determination may need to be performed again. For example, traffic through a failed router should be switched to a working router. Likewise, it may be possible to reroute traffic destined for a mobile node to a "mobility agent".
Note that when a node redoes next-hop determination there is no need to discard the complete Destination Cache entry. In fact, it is generally beneficial to retain such cached information as the PMTU and round trip timer values that may also be kept in the Destination Cache entry.
Routers and multihomed hosts have multiple interfaces. The remainder of this document assumes that all sent and received Neighbor Discovery messages refer to the interface of appropriate context. For example, when responding to a Router Solicitation, the corresponding Router Advertisement is sent out the interface on which the solicitation was received.
The conceptual data structures described above use different mechanisms for discarding potentially stale or unused information.
From the perspective of correctness there is no need to periodically purge Destination and Neighbor Cache entries. Although stale information can potentially remain in the cache indefinitely, the Neighbor Unreachability Detection algorithm ensures that stale information is purged quickly if it is actually being used.
To limit the storage needed for the Destination and Neighbor Caches, a node may need to garbage-collect old entries. However, care must be taken to insure that sufficient space is always present to hold the working set of active entries. A small cache may result in an excessive number of Neighbor Discovery messages if entries are discarded and rebuilt in quick succession. Any LRU-based policy that only reclaims entries that have not been used in some time (e.g., ten minutes or more) should be adequate for garbage-collecting unused entries.
A node should retain entries in the Default Router List and the Prefix List until their lifetimes expire. However, a node may garbage collect entries prematurely if it is low on memory. If not all routers are kept on the Default Router list, a node should retain at least two entries in the Default Router List (and preferably more) in order to maintain robust connectivity for off-link destinations.
When removing an entry from the Prefix List there is no need to purge any entries from the Destination or Neighbor Caches. Neighbor Unreachability Detection will efficiently purge any entries in these caches that have become invalid. When removing an entry from the Default Router List, however, any entries in the Destination Cache that go through that router must perform next-hop determination again to select a new default router.
This section describes router and host behavior related to the Router
Discovery portion of Neighbor Discovery. Router Discovery is used to
locate neighboring routers as well as learn prefixes and
configuration parameters related to address autoconfiguration.
Prefix Discovery is the process through which hosts learn the ranges of IP addresses that reside on-link and can be reached directly without going through a router. Routers send Router Advertisements that indicate whether the sender is willing to be a default router. Router Advertisements also contain Prefix Information options that list the set of prefixes that identify on-link IP addresses.
Stateless Address Autoconfiguration must also obtain subnet prefixes
as part of configuring addresses. Although the prefixes used for
address autoconfiguration are logically distinct from those used for
on-link determination, autoconfiguration information is piggybacked
on Router Discovery messages to reduce network traffic. Indeed, the
same prefixes can be advertised for on-link determination and address
autoconfiguration by specifying the appropriate flags in the Prefix
Information options. See [ADDRCONF] for details on how
autoconfiguration information is processed.
Hosts MUST silently discard any received Router Solicitation Messages.
A router MUST silently discard any received Router Solicitation messages that do not satisfy all of the following validity checks:
- The IP Hop Limit field has a value of 255, i.e., the packet could
not possibly have been forwarded by a router.
- If the message includes an IP Authentication Header, the message
authenticates correctly.
- ICMP Checksum is valid.
- ICMP Code is 0.
- ICMP length (derived from the IP length) is 8 or more octets.
- All included options have a length that is greater than zero.
The contents of the Reserved field, and of any unrecognized options, MUST be ignored. Future, backward-compatible changes to the protocol may specify the contents of the Reserved field or add new options; backward-incompatible changes may use different Code values.
The contents of any defined options that are not specified to be used with Router Solicitation messages MUST be ignored and the packet processed as normal. The only defined option that may appear is the Source Link-Layer Address option.
A solicitation that passes the validity checks is called a "valid solicitation".
A node MUST silently discard any received Router Advertisement messages that do not satisfy all of the following validity checks:
- IP Source Address is a link-local address. Routers must use their
link-local address as the source for Router Advertisement and
Redirect messages so that hosts can uniquely identify routers.
- The IP Hop Limit field has a value of 255, i.e., the packet could
not possibly have been forwarded by a router.
- If the message includes an IP Authentication Header, the message
authenticates correctly.
- ICMP Checksum is valid.
- ICMP Code is 0.
- ICMP length (derived from the IP length) is 16 or more octets.
- All included options have a length that is greater than zero.
The contents of the Reserved field, and of any unrecognized options, MUST be ignored. Future, backward-compatible changes to the protocol may specify the contents of the Reserved field or add new options; backward-incompatible changes may use different Code values.
The contents of any defined options that are not specified to be used with Router Advertisement messages MUST be ignored and the packet processed as normal. The only defined options that may appear are the Source Link-Layer Address, Prefix Information and MTU options.
An advertisement that passes the validity checks is called a "valid advertisement".
A router MUST allow for the following conceptual variables to be configured by system management. The specific variable names are used for demonstration purposes only, and an implementation is not required to have them, so long as its external behavior is consistent with that described in this document. Default values are specified to simplify configuration in common cases.
The default values for some of the variables listed below may be overridden by specific documents that describe how IPv6 operates over different link layers. This rule simplifies the configuration of Neighbor Discovery over link types with widely differing performance characteristics.
For each multicast interface:
AdvSendAdvertisements
A flag indicating whether or not the router sends
periodic Router Advertisements and responds to
Router Solicitations.
Default: FALSE
Note that AdvSendAdvertisements MUST be false by default so that a node will not accidentally start acting as a router unless it is explicitly configured by system management to send Router Advertisements.
MaxRtrAdvInterval
The maximum time allowed between sending unsolicited
multicast Router Advertisements from the interface,
in seconds. MUST be no less than 4 seconds and no
greater than 1800 seconds.
Default: 600 seconds
MinRtrAdvInterval
The minimum time allowed between sending unsolicited
multicast Router Advertisements from the interface,
in seconds. MUST be no less than 3 seconds and no
greater than .75 * MaxRtrAdvInterval.
Default: 0.33 * MaxRtrAdvInterval
AdvManagedFlag
The true/false value to be placed in the "Managed
address configuration" flag field in the Router
Advertisement. See [ADDRCONF].
Default: FALSE
AdvOtherConfigFlag
The true/false value to be placed in the "Other
stateful configuration" flag field in the Router
Advertisement. See [ADDRCONF].
Default: FALSE
AdvLinkMTU The value to be placed in MTU options sent by the
router. A value of zero indicates that no MTU
options are sent.
Default: 0
AdvReachableTime
The value to be placed in the Reachable Time field
in the Router Advertisement messages sent by the
router. The value zero means unspecified (by this
router). MUST be no greater than 3,600,000 milliseconds (1 hour).
Default: 0
AdvRetransTimer
The value to be placed in the Retrans Timer field in
the Router Advertisement messages sent by the
router. The value zero means unspecified (by this
router).
Default: 0
AdvCurHopLimit
The default value to be placed in the Cur Hop Limit
field in the Router Advertisement messages sent by
the router. The value should be set to that current
diameter of the Internet. The value zero means
unspecified (by this router).
Default: The value specified in the "Assigned Numbers" RFC [ASSIGNED] that was in effect at the time of implementation.
AdvDefaultLifetime
The value to be placed in the Router Lifetime field
of Router Advertisements sent from the interface, in
seconds. MUST be either zero or between
MaxRtrAdvInterval and 9000 seconds. A value of zero
indicates that the router is not to be used as a
default router.
Default: 3 * MaxRtrAdvInterval
AdvPrefixList
A list of prefixes to be placed in Prefix
Information options in Router Advertisement messages
sent from the interface.
Default: all prefixes that the router advertises via routing protocols as being on-link for the interface from which the advertisement is sent. The link- local prefix SHOULD NOT be included in the list of advertised prefixes.
Each prefix has an associated:
AdvValidLifetime
The value to be placed in the Valid Lifetime in the Prefix Information option, in seconds. The designated value of all 1's (0xffffffff) represents infinity.
Default: infinity.
AdvOnLinkFlag
The value to be placed in the on-link flag
("L-bit") field in the Prefix Information
option.
Default: TRUE
Automatic address configuration [ADDRCONF] defines additional information associated with each the prefixes:
AdvPreferredLifetime
The value to be placed in the Preferred
Lifetime in the Prefix Information option,
in seconds. The designated value of all 1's
(0xffffffff) represents infinity. See
[ADDRCONF].
Default: 604800 seconds (7 days)
AdvAutonomousFlag
The value to be placed in the Autonomous
Flag field in the Prefix Information option.
See [ADDRCONF].
Default: TRUE
The above variables contain information that is placed in outgoing Router Advertisement messages. Hosts use the received information to initialize a set of analogous variables that control their external behavior (see Section 6.3.2). Some of these host variables (e.g., CurHopLimit, RetransTimer, and ReachableTime) apply to all nodes including routers. In practice, these variables may not actually be present on routers, since their contents can be derived from the variables described above. However, external router behavior MUST be the same as host behavior with respect to these variables. In particular, this includes the occasional randomization of the ReachableTime value as described in Section 6.3.2.
Protocol constants are defined in Section 10.
The term "advertising interface" refers to any functioning and enabled multicast interface that has at least one unicast IP address assigned to it and whose corresponding AdvSendAdvertisements flag is TRUE. A router MUST NOT send Router Advertisements out any interface that is not an advertising interface.
An interface may become an advertising interface at times other than system startup. For example:
- changing the AdvSendAdvertisements flag on an enabled interface
from FALSE to TRUE, or
- administratively enabling the interface, if it had been
administratively disabled, and its AdvSendAdvertisements flag is
TRUE, or
- enabling IP forwarding capability (i.e., changing the system from
being a host to being a router), when the interface's
AdvSendAdvertisements flag is TRUE.
A router MUST join the all-routers multicast address on an advertising interface. Routers respond to Router Solicitations sent to the all-routers address and verify the consistency of Router Advertisements sent by neighboring routers.
A router sends periodic as well as solicited Router Advertisements out its advertising interfaces. Outgoing Router Advertisements are filled with the following values consistent with the message format given in Section 4.2:
- In the Router Lifetime field: the interface's configured
AdvDefaultLifetime.
- In the M and O flags: the interface's configured AdvManagedFlag and
AdvOtherConfigFlag, respectively. See [ADDRCONF].
- In the Cur Hop Limit field: the interface's configured CurHopLimit.
- In the Reachable Time field: the interface's configured
AdvReachableTime.
- In the Retrans Timer field: the interface's configured
AdvRetransTimer.
- In the options:
- In the "on-link" flag: the entry's AdvOnLinkFlag.
- In the Valid Lifetime field: the entry's
AdvValidLifetime.
- In the "Autonomous address configuration" flag: the
entry's AdvAutonomousFlag.
- In the Preferred Lifetime field: the entry's
AdvPreferredLifetime.
A router might want to send Router Advertisements without advertising itself as a default router. For instance, a router might advertise prefixes for address autoconfiguration while not wishing to forward packets. Such a router sets the Router Lifetime field in outgoing advertisements to zero.
A router MAY choose not to include some or all options when sending unsolicited Router Advertisements. For example, if prefix lifetimes are much longer than AdvDefaultLifetime, including them every few advertisements may be sufficient. However, when responding to a Router Solicitation or while sending the first few initial unsolicited advertisements, a router SHOULD include all options so that all information (e.g., prefixes) is propagated quickly during system initialization.
If including all options causes the size of an advertisement to exceed the link MTU, multiple advertisements can be sent, each containing a subset of the options.
A host MUST NOT send Router Advertisement messages at any time.
Unsolicited Router Advertisements are not strictly periodic: the
interval between subsequent transmissions is randomized to reduce the
probability of synchronization with the advertisements from other
routers on the same link [SYNC]. Each advertising interface has its
own timer. Whenever a multicast advertisement is sent from an
interface, the timer is reset to a uniformly-distributed random value
between the interface's configured MinRtrAdvInterval and
MaxRtrAdvInterval; expiration of the timer causes the next
advertisement to be sent and a new random value to be chosen.
For the first few advertisements (up to
MAX_INITIAL_RTR_ADVERTISEMENTS) sent from an interface when it
becomes an advertising interface, if the randomly chosen interval is
greater than MAX_INITIAL_RTR_ADVERT_INTERVAL, the timer SHOULD be set
to MAX_INITIAL_RTR_ADVERT_INTERVAL instead. Using a smaller interval
for the initial advertisements increases the likelihood of a router
being discovered quickly when it first becomes available, in the
presence of possible packet loss.
The information contained in Router Advertisements may change through actions of system management. For instance, the lifetime of advertised prefixes may change, new prefixes could be added, a router could cease to be a router (i.e., switch from being a router to being a host), etc. In such cases, the router MAY transmit up to MAX_INITIAL_RTR_ADVERTISEMENTS unsolicited advertisements, using the same rules as when an interface becomes an advertising interface.
An interface may cease to be an advertising interface, through actions of system management such as:
- changing the AdvSendAdvertisements flag of an enabled interface
from TRUE to FALSE, or
- administratively disabling the interface, or
- shutting down the system.
In such cases the router SHOULD transmit one or more (but not more than MAX_FINAL_RTR_ADVERTISEMENTS) final multicast Router Advertisements on the interface with a Router Lifetime field of zero. In the case of a router becoming a host, the system SHOULD also depart from the all-routers IP multicast group on all interfaces on
which the router supports IP multicast (whether or not they had been advertising interfaces). In addition, the host MUST insure that subsequent Neighbor Advertisement messages sent from the interface have the Router flag set to zero.
Note that system management may disable a router's IP forwarding capability (i.e., changing the system from being a router to being a host), a step that does not necessarily imply that the router's interfaces stop being advertising interfaces. In such cases, subsequent Router Advertisements MUST set the Router Lifetime field to zero.
A host MUST silently discard any received Router Solicitation messages.
In addition to sending periodic, unsolicited advertisements, a router sends advertisements in response to valid solicitations received on an advertising interface. A router MAY choose to unicast the response directly to the soliciting host's address (if the solicitation's source address is not the unspecified address), but the usual case is to multicast the response to the all-nodes group. In the latter case, the interface's interval timer is reset to a new random value, as if an unsolicited advertisement had just been sent (see Section 6.2.4).
In all cases, Router Advertisements sent in response to a Router Solicitation MUST be delayed by a random time between 0 and MAX_RA_DELAY_TIME seconds. (If a single advertisement is sent in response to multiple solicitations, the delay is relative to the first solicitation.) In addition, consecutive Router Advertisements sent to the all-nodes multicast address MUST be rate limited to no more than one advertisement every MIN_DELAY_BETWEEN_RAS seconds.
A router might process Router Solicitations as follows:
- Upon receipt of a Router Solicitation, compute a random delay within the range 0 through MAX_RA_DELAY_TIME. If the computed value corresponds to a time later than the time the next multicast Router Advertisement is scheduled to be sent, ignore the random delay and send the advertisement at the already-scheduled time. - If the router sent a multicast Router Advertisement (solicited or unsolicited) within the last MIN_DELAY_BETWEEN_RAS seconds, schedule the advertisement to be sent at a time corresponding to MIN_DELAY_BETWEEN_RAS plus the random value after the previous advertisement was sent. This ensures that the multicast Router
Advertisements are rate limited.
- Otherwise, schedule the sending of a Router Advertisement at the time given by the random value.
Note that a router is permitted to send multicast Router
Advertisements more frequently than indicated by the
MinRtrAdvInterval configuration variable so long as the more frequent
advertisements are responses to Router Solicitations. In all cases,
however, unsolicited multicast advertisements MUST NOT be sent more
frequently than indicated by MinRtrAdvInterval.
When a router receives a Router Solicitation and the Source Address is not the unspecified address, it records that the source of the packet is a neighbor by creating or updating the Neighbor Cache entry. If the solicitation contains a Source Link-Layer Address option, and the router has a Neighbor Cache entry for the neighbor, the link-layer address SHOULD be updated in the Neighbor Cache. If a Neighbor Cache entry is created for the source its reachability state MUST be set to STALE as specified in Section 7.3.3. If a cache entry already exists and is updated with a different link-layer address the reachability state MUST also be set to STALE. In either case the entry's IsRouter flag SHOULD be set to false.
If the Source Address is the unspecified address the router MUST NOT create or update the Neighbor Cache entry.
Routers SHOULD inspect valid Router Advertisements sent by other routers and verify that the routers are advertising consistent information on a link. Detected inconsistencies indicate that one or more routers might be misconfigured and SHOULD be logged to system or network management. The minimum set of information to check includes:
- Cur Hop Limit values (except for the unspecified value of zero). - Values of the M or O flags. - Reachable Time values (except for the unspecified value of zero). - Retrans Timer values (except for the unspecified value of zero). - Values in the MTU options. - Preferred and Valid Lifetimes for the same prefix.
Note that it is not an error for different routers to advertise different sets of prefixes. Also, some routers might leave some fields as unspecified, i.e., with the value zero, while other routers specify values. The logging of errors SHOULD be restricted to conflicting information that causes hosts to switch from one value to another with each received advertisement.
Any other action on reception of Router Advertisement messages by a router is beyond the scope of this document.
The link-local address on a router SHOULD change rarely, if ever. Nodes receiving Neighbor Discovery messages use the source address to identify the sender. If multiple packets from the same router contain different source addresses, nodes will assume they come from different routers, leading to undesirable behavior. For example, a node will ignore Redirect messages that are believed to have been sent by a router other than the current first-hop router. Thus the source address used in Router Advertisements sent by a particular router must be identical to the target address in a Redirect message when redirecting to that router.
Using the link-local address to uniquely identify routers on the link has the benefit that the address a router is known by should not change when a site renumbers.
If a router changes the link-local address for one of its interfaces, it SHOULD inform hosts of this change. The router SHOULD multicast a few Router Advertisements from the old link-local address with the Router Lifetime field set to zero and also multicast a few Router Advertisements from the new link-local address. The overall effect should be the same as if one interface ceases being an advertising interface, and a different one starts being an advertising interface.
None.
A host maintains certain Neighbor Discovery related variables in addition to the data structures defined in Section 5.1. The specific variable names are used for demonstration purposes only, and an implementation is not required to have them, so long as its external behavior is consistent with that described in this document.
These variables have default values that are overridden by information received in Router Advertisement messages. The default values are used when there is no router on the link or when all received Router Advertisements have left a particular value unspecified.
The default values in this specification may be overridden by specific documents that describe how IP operates over different link layers. This rule allows Neighbor Discovery to operate over links with widely varying performance characteristics.
For each interface:
LinkMTU The MTU of the link.
Default: The valued defined in the specific document that describes how IPv6 operates over the particular link layer (e.g., [IPv6-ETHER]).
CurHopLimit The default hop limit to be used when sending
(unicast) IP packets.
Default: The value specified in the "Assigned Numbers" RFC [ASSIGNED] that was in effect at the time of implementation.
BaseReachableTime
A base value used for computing the random
ReachableTime value.
Default: REACHABLE_TIME milliseconds.
ReachableTime The time a neighbor is considered reachable after receiving a reachability confirmation.
This value should be a uniformly-distributed random
value between MIN_RANDOM_FACTOR and
MAX_RANDOM_FACTOR times BaseReachableTime
milliseconds. A new random value should be
calculated when BaseReachableTime changes (due to
Router Advertisements) or at least every few hours
even if no Router Advertisements are received.
RetransTimer The time between retransmissions of Neighbor
Solicitation messages to a neighbor when resolving
the address or when probing the reachability of a
neighbor.
Default: RETRANS_TIMER milliseconds
The host joins the all-nodes multicast address on all multicast- capable interfaces.
When multiple routers are present, the information advertised collectively by all routers may be a superset of the information contained in a single Router Advertisement. Moreover, information may also be obtained through other dynamic means, such as stateful autoconfiguration. Hosts accept the union of all received information; the receipt of a Router Advertisement MUST NOT invalidate all information received in a previous advertisement or from another source. However, when received information for a specific parameter (e.g., Link MTU) or option (e.g., Lifetime on a specific Prefix) differs from information received earlier, and the parameter/option can only have one value, the most recently-received information is considered authoritative.
Some Router Advertisement fields (e.g., Cur Hop Limit, Reachable Time and Retrans Timer) may contain a value denoting unspecified. In such cases, the parameter should be ignored and the host should continue using whatever value it is already using. In particular, a host MUST NOT interpret the unspecified value as meaning change back to the default value that was in use before the first Router Advertisement was received. This rule prevents hosts from continually changing an internal variable when one router advertises a specific value, but other routers advertise the unspecified value.
On receipt of a valid Router Advertisement, a host extracts the source address of the packet and does the following:
- If the address is not already present in the host's Default Router
List, and the advertisement's Router Lifetime is non-zero, create a
new entry in the list, and initialize its invalidation timer value
from the advertisement's Router Lifetime field.
- If the address is already present in the host's Default Router List
as a result of a previously-received advertisement, reset its
invalidation timer to the Router Lifetime value in the newly-
received advertisement.
- If the address is already present in the host's Default Router List
and the received Router Lifetime value is zero, immediately time-
out the entry as specified in Section 6.3.5.
To limit the storage needed for the Default Router List, a host MAY choose not to store all of the router addresses discovered via advertisements. However, a host MUST retain at least two router addresses and SHOULD retain more. Default router selections are made whenever communication to a destination appears to be failing. Thus, the more routers on the list, the more likely an alternative working router can be found quickly (e.g., without having to wait for the next advertisement to arrive).
If the received Cur Hop Limit value is non-zero the host SHOULD set its CurHopLimit variable to the received value.
If the received Reachable Time value is non-zero the host SHOULD set its BaseReachableTime variable to the received value. If the new value differs from the previous value, the host SHOULD recompute a new random ReachableTime value. ReachableTime is computed as a uniformly-distributed random value between MIN_RANDOM_FACTOR and MAX_RANDOM_FACTOR times the BaseReachableTime. Using a random component eliminates the possibility Neighbor Unreachability Detection messages synchronize with each other.
In most cases, the advertised Reachable Time value will be the same in consecutive Router Advertisements and a host's BaseReachableTime rarely changes. In such cases, an implementation SHOULD insure that a new random value gets recomputed at least once every few hours.
The RetransTimer variable SHOULD be copied from the Retrans Timer field, if the received value is non-zero.
After extracting information from the fixed part of the Router Advertisement message, the advertisement is scanned for valid options. If the advertisement contains a Source Link-Layer Address option the link-layer address SHOULD be recorded in the Neighbor Cache entry for the router (creating an entry if necessary) and the IsRouter flag in the Neighbor Cache entry MUST be set to true. The IsRouter flag is used by Neighbor Unreachability Detection to determine when a router changes to being a host (i.e., no longer capable of forwarding packets). If a Neighbor Cache entry is created for the router its reachability state MUST be set to STALE as specified in Section 7.3.3. If a cache entry already exists and is updated with a different link-layer address the reachability state MUST also be set to STALE.
If the MTU option is present, hosts SHOULD copy the option's value into LinkMTU if the value does not exceed the default LinkMTU value specified in the link type specific document (e.g., [IPv6-ETHER]).
Prefix Information options that have the "on-link" (L) flag set indicate a prefix identifying a range of addresses that should be considered on-link. Note, however, that a Prefix Information option with the on-link flag set to zero conveys no information concerning on-link determination and MUST NOT be interpreted to mean that addresses covered by the prefix are off-link. The default behavior (see Section 5.2) when no information is known about an address is to send the packets to a default router and the reception of a Prefix Information option with the "on-link " (L) flag set to zero does not change this behavior. The reasons for an address being treated as on-link is specified in the definition of "on-link" in Section 2.1. Prefixes with the on-link flag set to zero would normally have the autonomous flag set and be used by [ADDRCONF].
For each Prefix Information option with the on-link flag set, a host does the following:
- If the prefix is the link-local prefix, silently ignore the Prefix
Information option.
- If the prefix is not already present in the Prefix List, and the
Prefix Information option's Valid Lifetime field is non-zero,
create a new entry for the prefix and initialize its invalidation
timer to the Valid Lifetime value in the Prefix Information option.
- If the prefix is already present in the host's Prefix List as the
result of a previously-received advertisement, reset its
invalidation timer to the Valid Lifetime value in the Prefix
Information option. If the new Lifetime value is zero, time-out
the prefix immediately (see Section 6.3.5).
- If the Prefix Information option's Valid Lifetime field is zero,
and the prefix is not present in the host's Prefix List, silently
ignore the option.
Note: Implementations can choose to process the on-link aspects of the prefixes separately from the address autoconfiguration aspects of the prefixes by, e.g., passing a copy of each valid Router Advertisement message to both an "on-link" and an "addrconf" function. Each function can then operate independently on the prefixes that have the appropriate flag set.
Whenever the invalidation timer expires for a Prefix List entry, that entry is discarded. No existing Destination Cache entries need be updated, however. Should a reachability problem arise with an existing Neighbor Cache entry, Neighbor Unreachability Detection will
perform any needed recovery.
Whenever the Lifetime of an entry in the Default Router List expires, that entry is discarded. When removing a router from the Default Router list, the node MUST update the Destination Cache in such a way that all entries using the router perform next-hop determination again rather than continue sending traffic to the (deleted) router.
The algorithm for selecting a router depends in part on whether or not a router is known to be reachable. The exact details of how a node keeps track of a neighbor's reachability state are covered in Section 7.3. The algorithm for selecting a default router is invoked during next-hop determination when no Destination Cache entry exists for an off-link destination or when communication through an existing router appears to be failing. Under normal conditions, a router would be selected the first time traffic is sent to a destination, with subsequent traffic for that destination using the same router as indicated in the Destination Cache modulo any changes to the Destination Cache caused by Redirect messages.
The policy for selecting routers from the Default Router List is as follows:
1) Routers that are reachable or probably reachable (i.e., in any state other than INCOMPLETE) SHOULD be preferred over routers whose reachability is unknown or suspect (i.e., in the INCOMPLETE state, or for which no Neighbor Cache entry exists). An implementation may choose to always return the same router or cycle through the router list in a round-robin fashion as long as it always returns a reachable or a probably reachable router when one is available.
2) When no routers on the list are known to be reachable or probably reachable, routers SHOULD be selected in a round-robin fashion, so that subsequent requests for a default router do not return the same router until all other routers have been selected.
Cycling through the router list in this case ensures that all
available routers are actively probed by the Neighbor
Unreachability Detection algorithm. A request for a default router
is made in conjunction with the sending of a packet to a router,
and the selected router will be probed for reachability as a side
effect.
3) If the Default Router List is empty, assume that all destinations are on-link as specified in